Huawei IPC6125-WDL-FA Configuration Manual Download Page 198

Page: 198 / 202

15.1.27 Failure To Enter The Full-Screen Mode Upon The First
Double-Click When Viewing Live Video On The Preview Tab
Page

Symptom

A user logs in to the IPC web client using the Firefox browser or Internet Explorer 11. On the

Preview

tab page, the user double-clicks the live video pane, but the live video pane does not

enter the full-screen mode.

Solution

This fault occurs only at the first double-click. Try once again.

15.1.28 The Button Is Blue After Functions In The Live Video
Preview Window Are Exited

Symptom

The user clicks

Full-Screen

and then exits the full screen mode. When the user moves

the pointer to the live video preview scope, the

Full-Screen

is blue.

The user clicks the

1:1

Snapshot

button and quickly moves the pointer to the live

video preview scope, the

1:1

Snapshot

button is blue.

Procedure

This does not affect functions. Move the pointer out of the live video preview scope, and the
buttons are displayed normally.

15.1.29 Users Are Unable To View Live Video

Symptom

After you access the web page of an IPC to view live video, a blank screen appears.

Possible Cause

No driver mapping the hardware display adapter (card) is installed, or the version of the
existing driver is too old.

Solution

Install a display adapter (card) driver or upgrade the existing display adapter (card) driver.

15.1.30 Live Video Image Artifacts Occur and The CPU Usage
Reaches 100%

Symptom

Live video image artifacts occur and the CPU usage reaches 100%.

IPC6125-WDL-FA
Configuration Guide

15 Appendix

Issue 01 (2016-08-20)

Huawei Proprietary and Confidential

192

Summary of Contents for IPC6125-WDL-FA











































































































































































































Search results

Summary of Contents for IPC6125-WDL-FA

Reviews:

Related manuals for IPC6125-WDL-FA

Brands by name

Popular brands

Huawei IPC6125-WDL-FA, Configuration Manual

Search results

Summary of Contents for IPC6125-WDL-FA

Reviews:

Related manuals for IPC6125-WDL-FA

Brands by name

Popular brands