Huawei IPC6125-WDL-FA Configuration Manual Download Page 102

Page: 102 / 202

Procedure

Step 1

Choose

Settings

PTZ Configuration

Preset Parameters

The

Preset Parameters

page is displayed, as shown in

Figure 8-4

Preset Parameters page

NOTE

Home position is a special preset to which a pan-tilt-zoom (PTZ) camera automatically rotates if users do
not control the rotation direction of the camera within a specified period.

The preset position numbered

is the home position by default. You can move the camera to a specified

position through the PTZ control panel and set the position as the home position.

If no home position is configured, the name displayed is

Home (Not set)

. If a home position is

configured, the name displayed is

Home (Custom location)

Home position cannot be deleted.

Step 2

Adjust the PTZ and determine a preset position.

Step 3

Click

Add

The page for

Add Preset

is displayed, as shown in

Figure 8-5

Add Preset

Step 4

Select a preset number and enter a name for the preset position.

IPC6125-WDL-FA
Configuration Guide

8 Setting PTZ Control Parameters

Issue 01 (2016-08-20)

Huawei Proprietary and Confidential

Summary of Contents for IPC6125-WDL-FA











































































































































































































Search results

Summary of Contents for IPC6125-WDL-FA

Reviews:

Related manuals for IPC6125-WDL-FA

Brands by name

Popular brands

Huawei IPC6125-WDL-FA, Configuration Manual

Search results

Summary of Contents for IPC6125-WDL-FA

Reviews:

Related manuals for IPC6125-WDL-FA

Brands by name

Popular brands