Huawei IPC6122-P Configuration Manual Download Page 94

Page: 94 / 115

12.7 Viewing Media Stream Parameters

You can view media stream parameters to understand the current media stream status.

Procedure

Step 1

Choose

Settings

System Configuration

Media Stream Information

The

Media Stream Information

page is displayed.

Step 2

View media stream parameters.

Table 12-6

describes the media stream parameters.

NOTE

Media stream parameters are read-only.

Table 12-6

Parameter description

Parameter

Description

NO.

Type

Type of the current media stream.
Options: TCP unicast, UDP unicast, and UDP
multicast.

Stream transmit type

Transmission type of the current media stream.
Options: elementary stream and program stream.

NOTE

If the IPC is registered with the video surveillance
platform using ONVIF, media streams are transmitted
as elementary streams.

If the IPC is registered with the video surveillance
platform using GB/T 28181, media streams are
transmitted as program streams.

Status

Transmission status of the current media stream.

Code stream type

Type of the current media stream transmitted by the
IPC.

Encryption type

Encryption type of the current media stream.

Unicast

IP address

IP address for receiving video and audio streams.

Audio port

Port number for receiving audio streams.

Video port

Port number for receiving video streams.

Multicast

IP address

Multicast IP address for receiving video and audio
streams.

Audio port

Multicast port number for receiving audio streams.

Video port

Multicast port number for receiving video streams.

Water mark

Indicates whether to enable the watermark function.

IPC6122-P
Configuration Guide

12 Managing the System

Issue 02 (2016-04-06)

Huawei Proprietary and Confidential

Summary of Contents for IPC6122-P




















































































































Search results

Summary of Contents for IPC6122-P

Reviews:

Related manuals for IPC6122-P

Brands by name

Popular brands

Huawei IPC6122-P, Configuration Manual

Search results

Summary of Contents for IPC6122-P

Reviews:

Related manuals for IPC6122-P

Brands by name

Popular brands