Huawei IDS1000 User Manual Download Page 60

Page: 60 / 67

IDS1000 Container Data Center
User Manual

7 Parts Replacement

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

Step 2

Use a flat-head screwdriver to pry off the cover of the emergency start/abort switch from the
base.

Step 3

Connect the cable to a new emergency start/abort switch using a Phillips screwdriver. Ensure
that the polarities of the cable are correct.

Power on the emergency start/abort switch only after the cable is correctly connected.

Step 4

Use a Phillips screwdriver to tighten the screws on the new emergency start/abort switch.

Step 5

Check that the emergency start/abort switch is working properly.

----End

Follow-up Procedure

Send the faulty emergency start/abort switch together with a

Repair Notice

to your local

Huawei office for repair.

7.9 Replacing a VESDA

For details about how to replace a VESDA, see the documents delivered with the VESDA or
contact Huawei technical support.

Summary of Contents for IDS1000




































































Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands

Huawei IDS1000, User Manual

Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands