Huawei IDS1000 User Manual Download Page 46 | Manualshive

Page: 46 / 67

background image

IDS1000 Container Data Center
User Manual

6 Troubleshooting

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

40

If no, go to

Step 3

Check the connection between the gas release indicator and the controller.

Use a multimeter to check whether there is any short circuit or open circuit.

Y => Rectify the connection fault.

Check whether the fault is rectified.

If yes, no further action is required.

If no, contact Huawei technical support.

N => Contact Huawei technical support.

----End

6.4 Audible and Visual Alarm Fault

Possible Causes



The power supply to the audible and visual alarm is abnormal.



The audible and visual alarm is faulty.



The cable connection of the audible and visual alarm is abnormal.

Tools and Materials



Multimeter



Screwdriver



Step ladder

Procedure

Step 1

Check the power supply to the audible and visual alarm.

Trigger a smoke alarm and a temperature alarm when the cable is removed from the solenoid
valve, and observe whether audible and visual alarms are generated. Use a multimeter to
measure the DC24V+ and GND terminals of the audible and visual alarm, and check whether
the voltage is within normal range.

Y => Go to

N => Regulate the voltage to a normal value.

Check whether the fault is rectified.



If yes, no further action is required.



If no, go to

Step 2

Replace the audible and visual alarm.

Check whether the fault is rectified.



If yes, no further action is required.



If no, go to

«
...
44
45
46
47
48
...
»

Summary of Contents for IDS1000




































































Reviews:

No comments

Related manuals for IDS1000

Brand: Warner Electric Pages: 3

Brand: iCeeO2 Pages: 7

Brand: SABAF Pages: 6

Brand: CALEFFI Pages: 2

Brand: CALEFFI Pages: 12

Brand: Caliber Pages: 6

Brand: PACH & COMPANY Pages: 4

Brand: T&S Pages: 5

Brand: WAM Pages: 62

Brand: walimex Pages: 7

Brand: Walchem Pages: 2

Brand: Walchem Pages: 73

Brand: Walchem Pages: 126

Brand: wallas Pages: 2

Brand: IDTECK Pages: 12

Brand: Banner Pages: 2

CGLine+ Web Controller

Brand: Eaton Pages: 28

Brand: OJ Electronics Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands