Huawei iBattery 3.0 User Manual Download Page 86

Page: 86 / 89

iBattery 3.0
User Manual

A Technical Specifications

Issue 07 (2019-12-30)

Technical Specifications

Environmental requirements

Item

iBOX

iBAT

Operating temperature

–20°C to +65°C

Storage temperature

–40°C to +80°C

–40°C to +70°C

Relative humidity

5% RH to 95% RH

Altitude

0–4000 m

At 2000–4000 m, high-temperature derating applies, and
the operating temperature decreases by 1°C for each
additional 200 m.

iBOX EMC specifications

Item

Specifications

Conducted emission

EN55032

Radiated emission (RE)

EN55032

Electrostatic discharge (ESD)

IEC61000-4-2

Electrical fast transient (EFT)

IEC61000-4-4

Radiated susceptibility (RS)

IEC61000-4-3

Conducted susceptibility (CS)

IEC61000-4-6

Surge immunity

IEC61000-4-5

Voltage dips

IEC61000-4-29

Power magnetic susceptibility (PMS)

IEC61000-4-8

iBAT EMC specifications

Summary of Contents for iBattery 3.0


























































































Search results

Summary of Contents for iBattery 3.0

Reviews:

Related manuals for iBattery 3.0

Brands by name

Popular brands

Huawei iBattery 3.0, User Manual

Search results

Summary of Contents for iBattery 3.0

Reviews:

Related manuals for iBattery 3.0

Brands by name

Popular brands