Huawei G5500 User Manual Download Page 138

Page: 138 / 215

Figure 6-4

Opening the fixing clips on the DIMM slot

Step 7

Align the DIMM with the DIMM slot, and insert the DIMM into the slot by gently pressing it
down until it sits flush with the slot. See

Figure 6-5

The two fixing clips pop up into place automatically.

Figure 6-5

Installing a DIMM

----End

6.2.3.8 Air Duct

Installing an Air Duct

Step 1

Power off the G560. For details, see

3.1 Powering Off the Compute Node

Step 2

Remove the G560. For details, see

3.3 Removing the G560

Step 3

Place the G560 on the ESD floor.

Step 4

Remove the cover. For details, see

3.7 Cover

Step 5

Installing a DIMM. For details, see Installing a DIMM.

Step 6

Vertically place the air duct downwards. See

Figure 6-6

FusionServer G5500 Server
User Guide

6 Optional Part Installation

Issue 02 (2017-12-15)

Huawei Proprietary and Confidential

130

Summary of Contents for G5500
























































































































































































































Search results

Summary of Contents for G5500

Reviews:

Brands by name

Popular brands

Huawei G5500, User Manual

Search results

Summary of Contents for G5500

Reviews:

Brands by name

Popular brands