Huawei FusionModule2000 V500R003C10 Product Description Download Page 129

Page: 129 / 217

FusionModule2000 Smart Modular Data Center
Product Description

7 Temperature Control System

Issue 06 (2020-05-21)

121

−

Compared with a traditional electrode humidifier, the wet film humidifier has a
longer service life and maintenance interval.



Condensate pump

The water pump provides power for top drainage with a maximum lift of 4 m.



Check valve

The check valve effectively prevents gas or liquid backflow.



Differential pressure switch

When the air filter is dirty or blocked, the differential pressure switch triggers an alarm,
prompting for air filter replacement.



T/H sensor

Built-in negative temperature coefficient (NTC) temperature sensors and return air T/H
sensor are provided.

7.4.2 Operating Environment Requirements

Physical ports

Table 7-17

Physical ports

Item

Specifications

Indoor unit

Refrigerant liquid pipe

Outer diameter of 5/8 inch (15.88 mm),
welding

Refrigerant gas pipe

Outer diameter of 7/8 inch (22.22 mm),
welding

Humidifier water inlet pipe

G 1/2 inch inner screw thread (humidifier
hose is provided for the smart cooling
product)

G 3/4 inch outer screw thread (humidifier
hose is not provided for the smart cooling
product)

Drainpipe

BSPP 1/2 inch inner screw thread

Outdoor unit

Refrigerant liquid pipe

Outer diameter of 5/8 inch (15.88 mm),
welding

Refrigerant gas pipe

Outer diameter of 7/8 inch (22.22 mm),
welding

water cooling
module

Refrigerant liquid pipe

Outer diameter of 5/8 inch (15.88 mm),
welding

Refrigerant gas pipe

Outer diameter of 7/8 inch (22.22 mm),
welding

Low-temperat
ure component
(optional
component)

Connecting to indoor unit
liquid pipe

Outer diameter of 5/8 inch (15.88 mm),
welding

Connecting to indoor unit
gas pipe

Outer diameter of 7/8 inch (22.22 mm),
welding

Summary of Contents for FusionModule2000 V500R003C10


























































































































































































































Search results

Summary of Contents for FusionModule2000 V500R003C10

Reviews:

Related manuals for FusionModule2000 V500R003C10

Brands by name

Popular brands

Huawei FusionModule2000 V500R003C10, Product Description

Search results

Summary of Contents for FusionModule2000 V500R003C10

Reviews:

Related manuals for FusionModule2000 V500R003C10

Brands by name

Popular brands