Huawei FusionModule1000A20 Installation Manual Download Page 32

Page: 32 / 107

FusionModule1000A20 Prefabricated All-in-One Data
Center
Installation Guide

4 Installing Pre-fab. Modules

Issue 02 (2020-01-15)

It is recommended that you tighten the base twistlocks after pre-fab. modules are hoisted in place.

----End

4.2.2 Removing the Pre-fab. Module Protective Cover

Prerequisites

The weather condition is good without rain or snow.

Context

A protective cover is installed to protect the pre-fab. module during transportation.

Preparations

Tools: safety helmet, safety belt, step ladder, protective gloves, utility knife

Materials: none

Skill requirement: common technician

Procedure

Step 1

Cut open the protective cover using a utility knife and remove the protective cover.

When removing the protective cover, take protective measures for working at heights.

----End

4.2.3 Hoisting and Securing Pre-fab. Modules

Prerequisites

To facilitate subsequent installation, ensure that pre-fab. modules are level after hoisting.



Select an appropriate crane based on standards of the crane company, and ask a
professional to assess the crane onsite.



Twistlocks in pre-fab. module bases are in correct positions.



The hoisting ropes are available.



The doors of pre-fab. modules to be hoisted are closed.



Ensure that the weather condition is good without wind when pre-fab. modules need to
be hoisted outdoors.

Summary of Contents for FusionModule1000A20












































































































Search results

Summary of Contents for FusionModule1000A20

Reviews:

Related manuals for FusionModule1000A20

Brands by name

Popular brands

Huawei FusionModule1000A20, Installation Manual

Search results

Summary of Contents for FusionModule1000A20

Reviews:

Related manuals for FusionModule1000A20

Brands by name

Popular brands