Huawei FusionModule1000A Installation Manual Download Page 99

Page: 99 / 108

FusionModule1000A40 Prefabricated All-in-One Data
Center
Installation Guide

A A Basic Installation Operations

Issue 03 (2020-06-09)

Figure A-9

Applying sealant

Step 9

Spray water to test the waterproof performance of the DPJ end connector.

----End

A.1.6.2 Installing Waterproof Metal Connectors

Prerequisites



Do not operate a feeder window outdoors under bad weather conditions if no shelter is
available.



Cables have been mounted on cable trays.



Cables need to be routed into a feeder window using waterproof metal connectors.

Preparations

Tool: wrench dedicated for the feeder window

Materials: transparent sealant, sealing rubber strip

Documents: none

Skill requirement: skilled technician

Procedure

Step 1

Disassemble a waterproof metal connector using the dedicated feeder window wrench shipped
with the pre-fab. module, and take the plug out of the connector, as shown in

Figure A-10

Summary of Contents for FusionModule1000A













































































































Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands

Huawei FusionModule1000A, Installation Manual

Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands