Huawei FusionModule1000A Installation Manual Download Page 53

Page: 53 / 108

FusionModule1000A40 Prefabricated All-in-One Data
Center
Installation Guide

7 Removing Transport Protection Materials

Issue 03 (2020-06-09)

7.2 Removing the Cabinet Sliding Base Fasteners

Prerequisites

The pre-fab. module has been installed and secured.

Preparations

Tool: adjustable wrench

Materials: none

Documents: none

Skill requirement: common technician

Context



The cabinets inside a pre-fab. module can be slid forward or backward on sliding bases.



To prevent cabinets from sliding during pre-fab. module transportation, two fasteners are
secured to the front and rear of the cabinet sliding base respectively. After the pre-fab.
module is installed and secured, the fasteners need to be removed.

Procedure

Step 1

Remove the bolts securing the cabinet sliding base fasteners using an adjustable wrench, and
remove the fasteners.

Figure 7-5

Removing the cabinet sliding base fasteners

Summary of Contents for FusionModule1000A













































































































Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands

Huawei FusionModule1000A, Installation Manual

Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands