Huawei FusionModule 1000A40 Maintenance Manual Download Page 155

Page: 155 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

5 Components Replacement

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

147

Figure 5-76

Disconnecting the fire cylinder and fire extinguishing pipeline

Remove the I-shaped connection pipe.

Remove the threaded adapter from the container valve of the fire cylinder, as shown by
(2) in

Figure 5-76

Step 5

Remove the pressure operated switch hose from the container valve of the fire cylinder.

Step 6

Remove the screws securing the fire cylinder using a Phillips screwdriver, and remove the fire
cylinder fasteners.

Step 7

Remove the faulty fire cylinder from the installation position.

Step 8

Move the new fire cylinder to the installation position, and tighten the fire cylinder fasteners.

Keep the pressure gauge panel outwards so that people can view the reading.

Step 9

Connect the hose to the pressure operated switch.

Wrap the threads with sealing tape to ensure air tightness.

Step 10

Connect the fire cylinder to the fire extinguishing pipeline.

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands