Huawei FusionDC1000A Installation Manual Download Page 121

Page: 121 / 130

A.1.6.2 Installing Waterproof Metal Connectors

Prerequisites

●

Do not operate a feeder window outdoors under bad weather conditions if no

shelter is available.

●

Cables have been mounted on cable trays.

●

Cables need to be routed into a feeder window using waterproof metal

connectors.

Preparations

Tool: wrench dedicated for the feeder window
Materials: transparent sealant, sealing rubber strip
Skill requirement: skilled technician

Procedure

Step 1 Disassemble a waterproof metal connector using the dedicated feeder window

wrench shipped with the pre-fab. module, and take the plug out of the connector.

Figure A-10 Disassembling a waterproof metal connector

Step 2 Route a cable into the pre-fab. module through the waterproof metal connector.

NO TICE

● People inside and outside the pre-fab. module should work together to route

the armored power cable to the specified connection position inside the pre-

fab. module.

● To facilitate operation during internal routing, you can remove some top plate

in the pre-fab. module aisle.

FusionDC1000A Prefabricated All-in-One Data

Center

Installation Guide (IT Scenario)

A Basic Installation Operations

Issue 01 (2021-04-20)

114

Summary of Contents for FusionDC1000A



































































































































Search results

Summary of Contents for FusionDC1000A

Reviews:

Related manuals for FusionDC1000A

Brands by name

Popular brands

Huawei FusionDC1000A, Installation Manual

Search results

Summary of Contents for FusionDC1000A

Reviews:

Related manuals for FusionDC1000A

Brands by name

Popular brands