manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

NO TE

During movement, do not tilt it for 90

o

.

Procedure

Step 1 Check that the external package of the unit is intact. If any damage is found,

notify the carrier immediately.

Step 2 Remove the packing materials. Check whether the exterior of the unit is in good

condition and free of collision marks or scratches. If any damage is found, notify

the carrier immediately.

NO TE

● Do not remove the plastic package to prevent dust and other sundries from entering the

unit. Remove the plastic packing materials before connecting pipes and cables.

● After pipes and cables are connected, take dustproof measures in a timely manner

based on site requirements.

Step 3 Check the type and quantity of fittings against the packing list. If some fittings are

missing or do not comply with the models in the packing list, record the

information and contact the supplier immediately.

----End

5.4.2 Securing a Unit

Context

Figure 5-3 Port reserved for combining smart cooling products

(1) Reserved port for combining units on the

end

(2) Reserved port for combining units on the

side

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

5 System Installation (FDC Scenario)

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

74

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

WarmPool DC55 Installation & Operation Manual preview
DC55
Brand: WarmPool Pages: 18
Xiaomi G11 Quick Start Manual preview
G11
Brand: Xiaomi Pages: 64
Kärcher VC 6 Cordless ourFamily Manual preview
VC 6 Cordless ourFamily
Brand: Kärcher Pages: 164
Kärcher WD 3 Original Instructions Manual preview
WD 3
Brand: Kärcher Pages: 40
Parkside PNTS 1500 B3 Original Instructions Manual preview
PNTS 1500 B3
Brand: Parkside Pages: 36
ZINEXTS MagPurix 24 EVO User Manual preview
MagPurix 24 EVO
Brand: ZINEXTS Pages: 36
Daitsu DS-9KIDB Service Manual preview
DS-9KIDB
Brand: Daitsu Pages: 21
XPower X-2000 Series Owner'S Manual preview
X-2000 Series
Brand: XPower Pages: 20
Vaclensa PLC Vaclensa CW20 Original Instructions Manual preview
Vaclensa CW20
Brand: Vaclensa PLC Pages: 12
Sunbeam 2587 Instruction Manual preview
2587
Brand: Sunbeam Pages: 5
Shark S3701UKL Owner'S Manual preview
S3701UKL
Brand: Shark Pages: 9
Hyundai HYUAP580 Instruction Manual preview
HYUAP580
Brand: Hyundai Pages: 52
Tiger MEA-A Instructions Manual preview
MEA-A
Brand: Tiger Pages: 6
inventum AC907W Instruction Manual preview
AC907W
Brand: inventum Pages: 100
Trion Air Boss T1001 Module Installation And Service Manual preview
Air Boss T1001 Module
Brand: Trion Pages: 23
Nilfisk-Advance GD 5 BATTERY Service Manual preview
GD 5 BATTERY
Brand: Nilfisk-Advance Pages: 20
Zibro P 24 Operating Manual preview
P 24
Brand: Zibro Pages: 166
Seifert 874020201USL Manual preview
874020201USL
Brand: Seifert Pages: 23

Brands by name

Popular brands

Load more brands