Huawei FusionCol8000-E24 User Manual Download Page 76

Page: 76 / 269

System Installation (FDC Scenario)

5.1 Installation Requirements

5.1.1 Installation Precautions

Checking the Auxiliary Facilities

●

It is recommended that the strength level of the concrete foundation be

higher than C20.

●

The surface of the concrete foundation should be flat and clean.

Checking the Drainage Capacity

There should be drainage ditches with sufficient drainage capacity.

NO TICE

The layout and installation of pipes should facilitate the maintenance of the unit.

Checking Electrical Access for Auxiliaries

Install the unit in strict accordance with the HVAC system construction regulations.

To ensure proper operation of the unit, protect it against dust, dirt, corrosive gas,

and high humidity.

Connection Engineering Precautions

●

Air duct installation: It is recommended that flexible connections be used

between the unit and air duct. Prepare air ducts based on site requirements.

●

Pipe thermal insulation: Take thermal insulation measures for all inlet pipes

and drainpipes of the FusionCol8000-E. Reserve sufficient space for

maintenance and operations when installing thermal insulation foam for

valves and connectors. At low temperatures, take thermal insulation measures

to prevent water pipes from freezing.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

5 System Installation (FDC Scenario)

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands