Huawei FusionCol8000-E24 User Manual Download Page 72

Page: 72 / 269

Figure 4-33 Installing an air deflector

----End

4.7 (Optional) Installing T/H Sensors Outside the Unit

and Cables

Context

T/H sensors outside the unit are used to detect the temperature and humidity in

the hot and cold aisles. The installation positions can be determined based on site

requirements. It is recommended that you deploy them in places where heat

sources are concentrated or where cooling capacity is most likely to be lacking.

The sensors must not face the air outlet of the unit.

Procedure

Step 1 Connect the indoor cold aisle T/H sensor and indoor supply air T/H sensor in

series.

Step 2 Connect the indoor hot aisle T/H sensor and indoor return air T/H sensor of the

heat exchanger core in series.

Figure 4-34 Connecting T/H sensors in series

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (Building Scenario)

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands