manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

2.2.2 Product Introduction (FDC Scenario)

Figure 2-4 Components (exterior)

(1) Indoor air return

vent (end)

(2) Outdoor air intake

vent (end)

(3) Indoor air supply

vent (end)

(4) Adjustable side

panel

(5) Electric control box (6) Maintenance door (7) Outdoor air

exhaust vent (end)

(8) Outdoor air

exhaust vent (top)

(9) Indoor air return

vent (side)

NO TE

The outdoor air exhaust vent is selected based on the actual situation.

Figure 2-5 Components (interior)

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

2 Product Description

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

17

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

TCF T Series Instruction, Operation And Maintenance Manual preview
T Series
Brand: TCF Pages: 19
Haier T-Series Service Manual preview
T-Series
Brand: Haier Pages: 56
iGenix IG9703 Instructions For Use Manual preview
IG9703
Brand: iGenix Pages: 9
Kärcher IVS 100/40 Original Operating Instructions preview
IVS 100/40
Brand: Kärcher Pages: 176
Kärcher SC 4 Quick Reference preview
SC 4
Brand: Kärcher Pages: 18
Keller AmbiCube Quick Start Manual preview
AmbiCube
Brand: Keller Pages: 2
Valex APL1221 Operating Instructions Manual preview
APL1221
Brand: Valex Pages: 16
Menuett 800-191 Operating Instructions Manual preview
800-191
Brand: Menuett Pages: 18
EdgeStar PUR700W Owner'S Manual preview
PUR700W
Brand: EdgeStar Pages: 14
Coopers F435 Instructions For Use preview
F435
Brand: Coopers Pages: 2
GE AEH10AL Owner'S Manual And Installation Instructions preview
AEH10AL
Brand: GE Pages: 32
Kärcher SC 5 Iron Kit Quick Reference preview
SC 5 Iron Kit
Brand: Kärcher Pages: 194
Kaysun KPD-35 DR12.1 Owner'S Manual preview
KPD-35 DR12.1
Brand: Kaysun Pages: 16
AirMaid AirMaid V Installation And Service Manual preview
AirMaid V
Brand: AirMaid Pages: 12
Daikin RXM71M2V1B Installation Manual preview
RXM71M2V1B
Brand: Daikin Pages: 20
Technibel GR360M3R5TA Series Installation Instructions Manual preview
GR360M3R5TA Series
Brand: Technibel Pages: 38
dibea GT100 Aurora Instruction Manual preview
GT100 Aurora
Brand: dibea Pages: 20
Fedders 23-23-0381N-002 s Installation & Operation Manual preview
23-23-0381N-002 s
Brand: Fedders Pages: 20

Brands by name

Popular brands

Load more brands