Huawei ECC800-Pro User Manual Download Page 87

Page: 87 / 368

Item

Temperature

Humidity

Power

consumption

< 280 mW

Storage

environment

–40°C to +70°C

Weight

About 85 g

3.2.20 Infrared Remote Control Module

Figure 3-44 Infrared remote control module

Table 3-72 Technical specifications of the infrared remote control module

Item

Specifications

Number of supported

remote control

commands

≤ 4

Communication

Interworks with the monitoring system over

Modbus-RTU to implement remote control.
The baud rate can be 9600 bit/s.

Infrared emission

distance

≤ 10 m

Power supply

9–16 V DC

Power

≤ 350 mA

Operating temperature

–10°C to +50°C

Operating humidity

5%–95% RH

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands