Huawei ECC800-Pro User Manual Download Page 126

Page: 126 / 368

Path

Parameter Name

Defaul

t Value

Description

QF1 Branch circuit breaker

in use (L1)
QF2 Branch circuit breaker

in use (L2)

Enable

When the

parameter is set to

Disable for a

branch, all alarms of

the branch will not

be reported.
When the

parameter is set to

Enable for a branch,

all alarms of the

branch will be

reported.

Upper load current

threshold

When the load

current exceeds the

preset value, an

alarm is generated.

Lower load current

threshold

When the load

current exceeds the

preset value, an

alarm is generated.

4. Set the parameters for other power distribution units in the same way or by

synchronizing parameters.

Path: Maintenance > Parameter Sync.

----End

5.6 Commissioning the eLight

If an eLight is installed, perform the following steps to configure it.

Procedure

Step 1 Ensure that the device address of the eLight actuator is the default value 2.

Toggle switches 1 to 4 of the DIP switch specify the device address in binary mode.

ON indicates 1, and OFF indicates 0.

Table 5-5 Setting a device address

Address

Toggle

Switch 1

Toggle

Switch 2

Toggle

Switch 3

Toggle

Switch 4

OFF

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

5 Power-On Commissioning

Issue 02 (2020-09-07)

115

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands