Huawei E8000E-X16 Manual Download Page 99

Page: 99 / 182

Figure 5-3

shows the panel SPUA02 (20G).

Figure 5-3

Panel of the SPUA02 (20G)

SPCA

SPUA

STATUS

SPCA

STATUS

SPUA

Buttons and Indicators

Table 5-1

shows the buttons and indicators on the SPUA panel.

Table 5-1

Buttons and indicators on the SPUA panel

Component

Description

OFL button

It is a button to send a application signal to the device when removing a
board. Before removing a board, you need to press and hold the

OFL

button

for about 6s till the

OFL

indicator is on.

OFL indicator
(Red)

If the indicator is on, you can remove the board.

RUN indicator
(Green)

If the indicator blinks once every 2s (0.5 Hz), it indicates that the board is
normal.
If the indicator blinks twice every 1s (2 Hz), it indicates that the board is in
alarm mode.

Table 5-2

shows the indicators on the SPC panel.

HUAWEI Eudemon8000E Firewall
Hardware Description

5 Boards

Issue 01 (2012-11-07)

Huawei Proprietary and Confidential

Summary of Contents for E8000E-X16























































































































































































Search results

Summary of Contents for E8000E-X16

Reviews:

Related manuals for E8000E-X16

Brands by name

Popular brands

Huawei E8000E-X16, Manual

Search results

Summary of Contents for E8000E-X16

Reviews:

Related manuals for E8000E-X16

Brands by name

Popular brands