Huawei E8000E-X16 Manual Download | Manualshive

Page: 155 / 182

background image

Indicator/
Button

Description

CF OFL button

If you press the CF OFL button, all operations on the CF card will be
ended and the CF card will be powered off.

SFP LINK/ACT
indicator (green)

If the indicator is steady on, it indicates that the link is normal.
If the indicator is blinking, it indicates that data is being transmitted.

MGMT-ETH
LINK indicator
(green) (on
Ethernet
interfaces)

If the indicator is steady on, it indicates that the link is normal.
If the indicator is off, it indicates that the link is down.

MGMT-ETH
ACT indicator
(amber) (on
Ethernet network
interfaces)

If the indicator is blinking, it indicates that data is being transmitted.
If the indicator is off, it indicates that no data is being transmitted.

A.2.4 SFU Indicators

lists the status and descriptions of SFU indicators.

Table A-8

Buttons and indicators on the panel of the SFU

LED

Description

RUN
(green)

Before the registration of the SFU: If the indicator blinks twice every second (2
Hz), it indicates that the system is in the alarm state.
After the registration of the SFU: If the indicator blinks once every two seconds
(0.5 Hz), it indicates that the system runs normally.

ACT
(green)

If the indicator is on, it indicates that the SFU works normally; if the green
indicator is off, it indicates that the SFU is faulty.

OFL (red) When the SFU works normally, the OFL indicator is off. After the OFL button

is pressed to power off the SFU, the OFL indicator is on.

A.3 Indicators of E8000E-X3

This chapter presents the indicators of E8000E-X3.

A.3.1 Fan Module Indicators

shows the status and description of the indicators.

HUAWEI Eudemon8000E Firewall
Hardware Description

A List of Indicators

Issue 01 (2012-11-07)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

145

«
...
153
154
155
156
157
...
»

Summary of Contents for E8000E-X16























































































































































































Reviews:

No comments

Related manuals for E8000E-X16

FortiGate 800/800F

Brand: Fortinet Pages: 54

Brand: HotBrick Pages: 89

Brand: SecureLogix Pages: 212

FortiTester 2000E

Brand: Fortinet Pages: 20

Brand: Pulse Secure Pages: 42

Brand: Pulse Secure Pages: 52

Brand: Meraki Pages: 5

Brand: FNGi Pages: 10

Hardware Firewall

Brand: Alpha Shield Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands