Huawei CX600-X1-M Series Hardware Description Download Page 23 | Manualshive

Page: 23 / 234

background image

LED

Colo
r

Nor
mal
Stat
us

Abn
orm
al
Stat
us

Exception Cause

Suggestion

The input fuse is
damaged.

Replace the rectifier.

Blink
ing

Being queried
manually.

Exit the query state.

Protection
LED

Yell
ow

off

on

Overtemperature
pre-alarm.

Ensure that the vent of the
rectifier is unblocked.

An AC input
undervoltage or
overvoltage occurs.

Ensure that the AC input
voltage is normal.

Blink
ing

Communication
between the
rectifier and an
external side is
interrupted.

Clean the golden finger
connection. If the protection
LED is still blinking, rectify
the fault on the external
module.

Fault LED

Red

off

on

Output overvoltage
occurs.

Remove the rectifier and
install it again. If there is still
no output, replace the
rectifier.

No output exists
because of a fault
inside the rectifier.

Replace the rectifier.

Blink
ing

Software is being
loaded.

The LED stops blinking when
the loading is complete.

1.3 Heat Dissipation System

The heat dissipation system is responsible for the heat dissipation of the entire device. Heat
generated by the boards is dissipated through the heat dissipation system. In this manner, the
temperatures of the components on the boards are controlled within a normal range, enabling
the boards to work stably. The heat dissipation system is composed of a fan frame, an air intake
vent, an air exhaust vent, and an air channel. All the fans in the fan frame work simultaneously,
and their rotation speeds can be adjusted by area. When one fan fails, the heat dissipation system
can still allow the device to work at an ambient temperature of 40°C (104°F) for a short period.
The temperature sensors, which are located on the air exhaust vent and boards, monitor the
temperatures of the components on the boards and adjust the fan rotation speeds according to
the commands delivered by the MPU to control the board temperatures.

HUAWEI CX600-X1-M/CX600-X2-M Series Metro
Services Platform
Hardware Description

1 CX600-X1-M4 Hardware Description

Issue 03 (2014-04-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

13

«
...
21
22
23
24
25
...
»

Summary of Contents for CX600-X1-M Series











































































































































































































































Reviews:

No comments

Related manuals for CX600-X1-M Series

Brand: IEI Technology Pages: 187

Brand: IEI Technology Pages: 71

Brand: Magma Pages: 2

Brand: Magnadyne Pages: 13

Brand: Maxim Pages: 26

Brand: NetComm Pages: 3

Brand: Opengear Pages: 2

Brand: ekwb Pages: 2

Brand: Commell Pages: 9

Brand: VCS Pages: 118

RCO-3000 Series

Brand: C&T Solution Pages: 96

Brand: TRENDnet Pages: 62

Digital Encoder Plus

Brand: IDT Pages: 98

DL-DVI-Vision-IP Series

Brand: G&D Pages: 228

CY62136EV30 MoBL

Brand: Cypress Semiconductor Pages: 12

Brand: Avenview Pages: 28

Brand: H3C Pages: 4

Brand: Ubiquiti Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands