Huawei CX600-X1-M Series Hardware Description Download Page 148

Page: 148 / 234

Item

Description

Connector X3

Cable connector-D style-9PIN-female

Cable type

Symmetrical twisted cable-120-ohm-
SEYVPV-0.5mm-24AWG-8core-PANTONE 430U

Symmetrical twisted cable-100-ohm-
SEYVP-0.48mm-26AWG-8core-black

Number of
cores

Fireproof class

Available
length

15 m ( 49.21 ft ) for the 120-ohm cable
3 m ( 9.84 ft ) for the 100-ohm cable

5.4 Auxiliary Port Cable

This section describes the structure and technical specifications of the AUX interface cable.

5.4.1 Introduction

The AUX interface cable is used to connect the AUX interface on the CX600 to a modem to
remotely transmit the configuration data of the CX600.

The AUX interface cable is an 8-core shielded cable. One end of the cable is an RJ45 connector
connected to the AUX interface on the MPU. The other end has DB9 and DB25 connectors,
either of which is connected to the serial interface on a computer.

NOTE

User login through AUX interfaces is not supported at present.

5.4.2 Structure

As shown in

Figure 5-2

the structure of the AUX interface cable is the same as that of the console

interface cable.

Table 5-9

shows the pin assignment on the AUX interface cable.

HUAWEI CX600-X1-M/CX600-X2-M Series Metro
Services Platform
Hardware Description

5 Cables

Issue 03 (2014-04-30)

Huawei Proprietary and Confidential

138

Summary of Contents for CX600-X1-M Series











































































































































































































































Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands

Huawei CX600-X1-M Series, Hardware Description

Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands