Huawei CX600-X1-M Series Hardware Description Download Page 142

Page: 142 / 234

Cables

About This Chapter

This chapter describes the structure and specifications of the external cables.

5.1 Power Cable

This section describes the structure and technical specifications of the power cable.

5.2 Chassis and Cabinet Grounding Cable

This section describes the structure and technical specifications of the chassis and cabinet ground
cable.

5.3 Console Port Cable

This section describes the structure and technical specifications of the console interface cable.

5.4 Auxiliary Port Cable

This section describes the structure and technical specifications of the AUX interface cable.

5.5 Clock Cable

This section describes the structure and technical specifications of the clock cable.

5.6 Ethernet Cable

Ethernet cables are classified into two types: straight-through cables and crossover cables.

5.7 Optical Fiber

This section describes the structure and technical specifications of the optical fiber.

5.8 16xE1 Cable

This section describes the structure and technical specifications of the 16xE1 cable.

5.9 75-ohm 155M Electrical Interface Optical Module Cable

This section describes the architecture and technical specifications of the 75-ohm 155M
electrical interface optical module cable.

5.10 Alarm Input/Output Cables

This section describes the structure and technical specifications of the Alarm Input/Output
Cables.

HUAWEI CX600-X1-M/CX600-X2-M Series Metro
Services Platform
Hardware Description

5 Cables

Issue 03 (2014-04-30)

Huawei Proprietary and Confidential

132

Summary of Contents for CX600-X1-M Series











































































































































































































































Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands

Huawei CX600-X1-M Series, Hardware Description

Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands