Huawei CX600-X1-M Series Hardware Description Download Page 122

Page: 122 / 234

Product Specifications

Table 4-38

shows the product specifications of the 4-Port Channelized STM-1c POS-SFP

Physical Interface Card(PIC).

Table 4-38

Product specifications of the 4-Port Channelized STM-1c POS-SFP Physical

Interface Card(PIC)

Item

Description

Protocol and services

Supporting 63 channels and 256 MP
groups

Connector type

SFP

Reliability and availability

Hardware feature

Supporting hot swapping

NMS

Supporting command line management
interfaces
Supporting SNMP and MIBs

Ambient operating conditions

Operating temperature: -40°C to +65°C
( -40°F to 149°F )
Long-term relative humidity: 5% to 85%
Short-term relative humidity: 5% to 95%

Ambient storage conditions

Storage temperature: -40°C to +70°C
( -40°F to 158°F )
Storage humidity: 0% to 95%

4.7 32-Port E1 Physical Interface Card(PIC, 75ohm)

Overview

The 32-Port E1 Physical Interface Card(PIC, 75ohm) is hot-swappable and provides up to 32
E1 interfaces. The service type of every interface can be configured flexibly.

Figure 4-7

shows the appearance of the 32-Port E1 Physical Interface Card(PIC, 75ohm).

Figure 4-7

Appearance of 32-Port E1 Physical Interface Card(PIC, 75ohm)

HUAWEI CX600-X1-M/CX600-X2-M Series Metro
Services Platform
Hardware Description

4 Boards

Issue 03 (2014-04-30)

Huawei Proprietary and Confidential

112

Summary of Contents for CX600-X1-M Series











































































































































































































































Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands

Huawei CX600-X1-M Series, Hardware Description

Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands