Huawei BTS3900 V100R003 Hardware Description Download Page 163

Page: 163 / 264

Functions

The PMU performs the following functions:

Communicates with the BBU or upper-level PMU through an RS232/RS422 serial port.

Manages the power system and battery charge/discharge.

Detects and reports water damage alarms, smoke alarms, door status alarms, and
customized Boolean values.

Reports the ambient temperature, ambient humidity, battery temperature, and customized
analog values.

Monitors power distribution, reports related alarms, and reports dry contact alarms.

Ports and LEDs

Figure 4-52

shows the front panel of the PMU.

Figure 4-52

Front panel of the PMU

(1) RS232/RS422 ports

(2) LEDs

(3) Power supply test ports

(4) TEST port

(5) Battery control switch

(6) COM port

Table 4-65

describes the ports and switch on the PMU.

Table 4-65

Ports and switch on the PMU

Port/Switch

Function

RS232/RS422 port

Communicating with the BBU or upper-level PMU

BTS3900
Hardware Description

4 BTS3900 Components

Issue 04 (2011-02-15)

Huawei Proprietary and Confidential

4-71

Summary of Contents for BTS3900 V100R003









































































































































































































































































Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands

Huawei BTS3900 V100R003, Hardware Description

Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands