Huawei AR530 Series Configuration Manual Download | Manualshive

Page: 113 / 408

background image

with the VLANIF interface of the super-VLAN. Some subnet IDs, default gateway addresses
of the subnets, and directed broadcast addresses of the subnets are saved and different broadcast
domains can use the addresses in the same subnet segment. As a result, subnet differences are
eliminated, addressing becomes flexible and idle addresses are reduced. VLAN aggregation
allows each sub-VLAN to function as a broadcast domain to implement broadcast isolation and
saves IP address resources.

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

interface

interface-type

interface-number

The interface view is displayed.

Step 3

Run:

port link-type

access

The link type of the interface is set to access.

Step 4

Run:

quit

Return to the system view.

Step 5

Run:

vlan

vlan-id

A sub-VLAN is created and the sub-VLAN view is displayed.

Step 6

Run:

port

interface-type

{

interface-number1

[

to

interface-number2

] } &<1-10>

A port is added to the sub-VLAN.

----End

3.6.3.2 Creating a Super-VLAN

Context

A super-VLAN consists of several sub-VLANs. No physical port can be added to a super-VLAN,
but a VLANIF interface can be configured for the super-VLAN and an IP address can be assigned
to the VLANIF interface.

NOTE

Before configuring a super-VLAN, ensure that sub-VLANs have been configured.

Huawei AR530&AR550 Series Industrial Switch Routers
Configuration Guide - Ethernet Switching

3 VLAN Configuration

Issue 01 (2014-11-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

99

«
...
111
112
113
114
115
...
»

Summary of Contents for AR530 Series

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for AR530 Series

ShareCenter Quattro DNS-345

Brand: D-Link Pages: 40

ShareCenter Quattro DNS-345

Brand: D-Link Pages: 4

ShareCenter DNS-343

Brand: D-Link Pages: 12

AirPlus G DWL-G710

Brand: D-Link Pages: 5

MYDLINK DNR-322L

Brand: D-Link Pages: 4

mydlink DNR-312L

Brand: D-Link Pages: 8

Brand: D-Link Pages: 12

Brand: D-Link Pages: 16

Brand: D-Link Pages: 88

Brand: Panasonic Pages: 4

Brand: ICP DAS USA Pages: 8

Brand: Fortinet Pages: 20

Brand: Black Box Pages: 37

Brand: Genie Pages: 15

Brand: ZyXEL Communications Pages: 125

Brand: Paradyne Pages: 23

Vigor 2760 Series

Brand: Draytek Pages: 54

IMACS Network Device

Brand: Zhone Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands