manualshive.com logo in svg

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 43 / 204

Share
Download
Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 43

Step 2

Save the settings.

----End

2.5.4 Setting SIP Parameters

When the Session Initiation Protocol (SIP) is used for video communications, the SIP parameters
of the terminal, such as whether to register with the SIP server, must be set.

Prerequisites

Both parties of the conference support SIP.

Procedure

Step 1

Choose 

Settings

 > 

Network

 > 

IP

 > 

SIP

, and then set the parameters listed in 

Table 2-6

.

Table 2-6

 SIP parameters

Parameter

Description

Register with server

This specifies whether the terminal registers with the SIP server.

l

Enable: After the terminal is registered with the SIP server
successfully, it can call a remote site using the site number, site
name, or IP address.

l

The terminal does not register with the SIP server, and it can call
another site using only the IP address.

Server address

This specifies the IP address of the SIP server.

Enable proxy
server

When the terminal needs to register with the IP multimedia subsystem
(IMS) for deploying services, enable the proxy server and set its
address.

NOTE

Borne by the standard IP protocol, the IMS uses voice over IP (VoIP)
applications based on the standard SIP applications of the 3rd Generation
Partnership Project (3GPP) to provide fixed and mobile multimedia services
for operators. Integrating MCUs can enhance the functionality of the Huawei
IMS HD videoconferencing solution.

Proxy server
address

The proxy server needs to forward the registration request from the
terminal to the SIP server in the IMS network when the terminal is
registering with the IMS network.

Conference service
number

Before initiating a conference from the terminal on an IMS network,
you need to set this parameter and ensure that the terminal setting is
consistent with the setting on the IMS network device. The conference
service number can be obtained from the administrator of the IMS
network device.

Site number

This specifies the site number of the local terminal. When the local
terminal is registered with the SIP server, another terminal can call
the local terminal using this site number. The site number can contain
only digits.

HUAWEI 9000 HD Video Terminal
Administrator Guide

2 Network

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

31

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments