manualshive.com logo in svg

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 14 / 204

Share
Download
Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 14

1.1 Overview

Before using a video terminal, the available terminal models, specifications, and main functions
should be understood so that a terminal can be properly selected and used.

The HUAWEI 9000 HD video terminal series (HUAWEI 9000 for short) is a series of new-
generation HD video terminals provided by Huawei. The HUAWEI 9000 adopts advanced
videoconferencing technologies to provide HD video and high-fidelity (hi-fi) audio.

The HUAWEI 9000 supports multiple types of audio-visual sources. With rich interfaces and
customizable settings, the HUAWEI 9000 provides a professional and personalized real-time
videoconferencing environment.

The HUAWEI 9000 consists of the following terminal models: ViewPoint 9039 (ViewPoint
9039-T and ViewPoint 9039-M), ViewPoint 9039S (ViewPoint 9039S-M), HUAWEI VP9036S
(HUAWEI VP9036S-M), ViewPoint 9036 (ViewPoint 9036-M), ViewPoint 9035, ViewPoint
9033, ViewPoint 9030, HUAWEI VP9039A (HUAWEI VP9039A-T, HUAWEI VP9039A-TS),
and HUAWEI VP9035A. In the preceding models, 

T

 or 

TS

 indicates that the corresponding

terminal is to be used in a Huawei telepresence system and 

M

 indicates that the corresponding

terminal provides a built-in Multipoint Control Unit (MCU).

NOTE

The HUAWEI VP9039A-TS does not support the simultaneous transmission of 1080p 30Hz or 720p 60Hz
video and presentation.

Table 1-1

 lists the maximum supported resolution and call bandwidth of the HUAWEI 9000

series models.

Table 1-1

 Differences between models in the HUAWEI 9000 series

Model

Maximum Video
Resolution

Maximum Call
Bandwidth

ViewPoint 9039

1080p

8 Mbit/s

ViewPoint 9036

720p

4 Mbit/s

ViewPoint 9035

720p

4 Mbit/s

ViewPoint 9033

720p (receive)
4CIF (send)

4 Mbit/s

ViewPoint 9030/ViewPoint
9030(1080p)

720p/1080p

4 Mbit/s

ViewPoint 9039S

1080p

8 Mbit/s

HUAWEI VP9039A

1080p

8 Mbit/s

HUAWEI VP9035A/
HUAWEI VP9035A(1080p)

720p/1080p

4 Mbit/s

HUAWEI VP9036S

1080p

8Mbit/s

 

HUAWEI 9000 HD Video Terminal
Administrator Guide

1 Installation and Preparation

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

2

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments