manualshive.com logo in svg

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 134 / 204

Share
Download
Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 134

2.

The function that corresponds to the status icon has been enabled or is available.

Choose 

Settings

 > 

Display

 > 

Icon

. Select the icons to be displayed on screens.

7.2 Adjusting Audio Effects

You can adjust the audio effects, such as the audio input, sound effect, volume, and stereo.

Context

For details about how to adjust the audio input, volume, and stereo, see 

4.3 Setting Audio

Parameters

. This section only describes how to adjust the sound effect.

Procedure

Step 1

Choose 

Settings

 > 

Audio

 > 

Sound Effect

, and then set the parameters listed in 

Table 7-3

.

Table 7-3

 Audio parameters

Parameter

Description

Network jitter

This is a sound adjustment method. A higher network jitter contributes
to a better audio connectivity. In a conference, the lip movements and
voice of a speaker may not be synchronous. To solve this problem,
users can adjust the network jitter value.
When the terminal uses a wired network for video communications, it
is recommended that you use the default value of this parameter.

Environmental
echo

l

Normal

: By default, this option is selected.

l

Loud

: When the echo of a remote site is loud, the local site needs

to notify the remote site and the remote site should set

Environmental echo

 to 

Loud

 so that the echo of the remote site

can be canceled.

Echo cancellation

You can enable or disable echo cancellation for the audio sources from
MIC1 and MIC2 interfaces of the terminal. By default, this function is
enabled.

Music mode

The setting of the music mode can take effect only when you set the
mode at the input end of the music. If the music mode is enabled at the
music input end, the music effect becomes better.

Ringtone

After a ringtone is selected, the terminal plays the ringtone when there
is an incoming call.

Audio channel
balance

In stereo mode, you can adjust the balance of the left and right audio
channels by moving the slider.

Bass
Middle
Treble

To achieve different audio effects, adjust the equalizers by moving the
sliders.

HUAWEI 9000 HD Video Terminal
Administrator Guide

7 Video and Audio

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

122

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments