manualshive.com logo in svg

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 107 / 204

Share
Download
Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 107

l

From the local site: Check that the site has been registered with the GK.

Step 2

Press   on the remote control to display the 

Call

 screen.

Step 3

Obtain the access number of the authentication conference.

Step 4

Set 

Type

 and 

Rate

. Select the highest rate supported by the local terminal for 

Rate

 to boost the

call success rate.

Step 5

Select 

Call

.

If no password is set for the authentication conference, the terminal can join the conference
directly after a language is specified.

If a terminal requests chair control rights during an authentication conference, the password for
the authentication conference (that is, the conference password) is required.

----End

Follow-up Procedure

The terminal joins the conference after it passes the authentication using the videoconferencing
system.

5.7 Joining an HD-Video Conference over an IMS Network

The terminal can join an HD video conference over an IMS network.

Context

Borne by the standard IP protocol, IMS uses VoIP applications based on the standard SIP
applications of the 3GPP to provide fixed and mobile multimedia services for operators.
Integrating MCUs can enhance the functionality of the Huawei IMS HD videoconferencing
solution.

Procedure

Step 1

Register the terminal with the network where the IMS is located. For details, see section 

2.5.4

Setting SIP Parameters

.

Step 2

Call the conference ID allocated by the IMS. For details, see 

5.6 Joining an Authentication

Conference

.

Step 3

Enter the password as prompted.

NOTE

Terminal users can obtain the conference ID and password allocated by the IMS from emails, text messages,
notices, or other methods.

----End

Result

After the IMS authenticates the password, the terminal can join an HD video conference over
an IMS network.

HUAWEI 9000 HD Video Terminal
Administrator Guide

5 Initiating a Conference

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

95

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments