Huawei 50082920 Hardware Installation And Maintenance Manual Download Page 96 | Manualshive

Page: 96 / 112

background image

l

For a network cable connecting a hub and device, the label on the hub end should
indicate the numbers of the chassis and cabinet where the hub resides, and the serial
number on the hub. The label on the device end should indicate the number of the
chassis and cabinet where the device is located. If the device is a standalone device,
provide the specific position of the device.

l

For a network cable connecting a hub and an agent or terminal, the label on the agent or
terminal end should contain the serial number of the network interface. The definitions
of the cabinet number and chassis number are the same as those described in

l

If the hub is a standalone device without a cabinet or chassis, the label should contain
specific location information that identifies the hub.

The serial number on the hub, the network interface number of the agent or terminal, and the
location of the standalone device should be specified according to actual connections.

Label Example

Figure 5-91

shows a sample label on an Ethernet cable.

Figure 5-91

Sample label on an Ethernet cable

A01

TO:

03

01

01

B02

03

01

Meaning of the label in

Figure 5-91

l

"A01-03-01-01" indicates that one end of the network cable is connected to network
interface 01 in slot 01, chassis 03 of the cabinet in row A, column 01 in the equipment
room.

l

"B02-03-01" indicates that another end of the network cable is connected to network
interface 01 in chassis 03 of the cabinet on row B, column 02 in the equipment room. No
slot number is given.

5.4.4 Engineering Labels for User Cables

Attach labels to both ends of a user cable to indicate the locations of the cable on the device
and main distribution frame (MDF).

Meaning of the Engineering Labels for User Cables

shows the contents of the labels.

Table 5-25

Contents of the engineering labels for user cables

Content

Meaning

Example

MN-B-C-D

MN: cabinet
number

For example, A01 is the first cabinet in row A.

R250D
Hardware Installation and Maintenance Guide

5 Appendix

Issue 01 (2016-09-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

90

«
...
94
95
96
97
98
...
»

Summary of Contents for 50082920

















































































































Reviews:

No comments

Related manuals for 50082920

Brand: Ebyte Pages: 11

Brand: Ubiquiti Pages: 32

AR 18-3XE/18-21X Series

Brand: H3C Pages: 79

Brand: Sercomm Pages: 76

ExtremeWireless WS-AP3915i-FCC

Brand: Extreme Networks Pages: 22

Brand: TP-Link Pages: 2

Brand: Atlantis Land Pages: 2

Brand: ZyXEL Communications Pages: 263

Brand: Billion Pages: 230

Brand: ARGtek Pages: 14

Brand: iBall Baton Pages: 62

Brand: Xirrus Pages: 3

Brand: IP-COM Pages: 15

Brand: IP-COM Pages: 63

Brand: Amer Pages: 59

Brand: XtendLan Pages: 23

Brand: HPE Pages: 4

Brand: UPT Solar Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands