Huawei 50082920 Hardware Installation And Maintenance Manual Download Page 94

Page: 94 / 112

Content

Meaning

Example

C: physical slot
number

Numbered in top-down and left-right order starting
from 01. For example, 01 is the first slot at the top left
of the chassis.

D: optical
interface
number.

Numbered in top-down and left-right order, consistent
with the port sequence number on the device.

R: Optical
receiving
interface
T: optical
transmitting
interface

ODF-MN-B-
C-R/T

MN: row
number and
column number
of an ODF

M: The cabinet rows from front to back are numbered
from A to Z.
N: The cabinet columns from left to right are
numbered from 01 to 99.
For example, G01 is the ODF of row G and column
01.

B: row number
of the terminal
device

Range from 01 to 99, for example, 01-01.

C: column
number of the
terminal device

R: Optical
receiving
interface
T: optical
transmitting
interface

Example of the Label

Figure 5-90

shows a sample label on an optical fiber.

Figure 5-90

Sample label on an optical fiber between the device and the ODF

ODF

TO:

G01 01

A01

R250D
Hardware Installation and Maintenance Guide

5 Appendix

Issue 01 (2016-09-30)

Huawei Proprietary and Confidential

Summary of Contents for 50082920

















































































































Search results

Summary of Contents for 50082920

Reviews:

Related manuals for 50082920

Brands by name

Popular brands

Huawei 50082920, Hardware Installation And Maintenance Manual

Search results

Summary of Contents for 50082920

Reviews:

Related manuals for 50082920

Brands by name

Popular brands