Huawei 50082920 Hardware Installation And Maintenance Manual Download Page 48

Page: 48 / 112

of the RJ45, and that the contact strip blade extends beyond the ends of the wires and is
crimped with the wires. If not, replace the connector.

Figure 5-37

shows an unqualified piece.

Figure 5-37

Wires not in good contact with the edge of the RJ45

----End

Testing the Connection of Assembled Cables

Context

Huawei provides two types of Ethernet cables: straight-through cables and crossover cables.

Straight-through cables are connected in a one-to-one manner. They are used to connect
terminals such as a computer or switch to network devices.

Table 5-7

lists the

connections of core wires in a straight-through cable.

Table 5-7

Connections of core wires in a straight-through cable

RJ45 Connector 1 RJ45 Connector 2 Core Wire Color

Twisted or Not

Orange

Twisted

Orange-White

Green

Twisted

Green-White

Blue

Twisted

Blue-White

Brown

Twisted

Brown-White

Crossover cables are connected in a crossover manner. They are used to connect
terminals such as two computers or switches.

Table 5-8

lists the connections of core

wires in a crossover cable.

R250D
Hardware Installation and Maintenance Guide

5 Appendix

Issue 01 (2016-09-30)

Huawei Proprietary and Confidential

Summary of Contents for 50082920

















































































































Search results

Summary of Contents for 50082920

Reviews:

Related manuals for 50082920

Brands by name

Popular brands

Huawei 50082920, Hardware Installation And Maintenance Manual

Search results

Summary of Contents for 50082920

Reviews:

Related manuals for 50082920

Brands by name

Popular brands