Huawei 50082920 Hardware Installation And Maintenance Manual Download Page 39 | Manualshive

Page: 39 / 112

background image

NOTICE

l

When you remove a section of the jacket, do not damage the shield layer of the twisted-
pair cable.

l

When you remove the shield layer, do not damage the insulation of the twisted-pair cable.

Figure 5-17

Removing the jacket of a twisted-pair cable (unit: mm (in.))

Step 3

Fit the metal shell onto the twisted-pair cable. The shield layer is covered by the metal shell,
as shown in

Figure 5-18

.

Figure 5-18

Fitting the metal shell onto the twisted-pair cable

Step 4

Fit the metal shell onto the twisted-pair cable until the shield layer is covered completely.
Along the edge of the metal shell, cut off the aluminum foil shield layer and ensure that there
is no surplus copper wire. The exposed twisted-pair cable is about 20 mm (0.79 in.) long, as
shown in

Figure 5-19

R250D
Hardware Installation and Maintenance Guide

5 Appendix

Issue 01 (2016-09-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

33

«
...
37
38
39
40
41
...
»

Summary of Contents for 50082920

















































































































Reviews:

No comments

Related manuals for 50082920

Brand: 3Com Pages: 6

Brand: Cambium Networks Pages: 196

Brand: Cambium Networks Pages: 478

Brand: Cambium Pages: 301

Brand: Cambium Networks Pages: 287

Brand: Airlink101 Pages: 7

Brand: Shiro Pages: 83

Brand: NetComm Pages: 55

Brand: NETGEAR Pages: 263

Brand: NETGEAR Pages: 2

Brand: Z-Com Pages: 23

Thunderbolt 3/USB-C I/ O CARD

Brand: Logicube Pages: 5

Brand: H3C Pages: 34

Brand: MikroTik Pages: 7

Brand: Caimore Pages: 83

Brand: SingTel Pages: 13

Brand: Air Live Pages: 72

Brand: EnGenius Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands