Huawei 50082920 Hardware Installation And Maintenance Manual Download Page 29

Page: 29 / 112

–

Cut all the exposed copper wires.

–

Try to avoid a second crimping of sleeves.

–

Keep all the conductors clean and aligned.

NOTE

The connectors, cables, and tools provided by different vendors may be different. The figures in this
document are for your reference only.

5.1.2 Assembling Power Cables

Assembling the OT Terminal and Power Cable

Context

Figure 5-1

shows the components of an OT terminal and a power cable.

Figure 5-1

Components of an OT terminal and a power cable

A. Heat-shrinkable tubing

B. Bare crimping terminal

C. Insulation

D. Conductor

Procedure

Step 1

Based on the cross-sectional area of the cable conductor, strip a length of insulation coating C
to expose the conductor D of length L1, as shown in

Figure 5-2

. The recommended values of

L1 are listed in

Table 5-1

R250D
Hardware Installation and Maintenance Guide

5 Appendix

Issue 01 (2016-09-30)

Huawei Proprietary and Confidential

Summary of Contents for 50082920

















































































































Search results

Summary of Contents for 50082920

Reviews:

Related manuals for 50082920

Brands by name

Popular brands

Huawei 50082920, Hardware Installation And Maintenance Manual

Search results

Summary of Contents for 50082920

Reviews:

Related manuals for 50082920

Brands by name

Popular brands