HTP SSC-119 Installation Manual Download Page 12

lp-65 Rev. 1.6.15

12

Part 6 - Maintenance and Troubleshooting

Periodic maintenance should be performed by a qualified service technician to ensure all equipment is operating safely and 
efficiently. The owner should make necessary arrangements with a qualified heating contractor for periodic maintenance of the 
heater. Installer must also inform the owner that the lack of proper water heater care and maintenance may result in hazardous 
conditions.

Annual Maintenance Activities

Date Last Completed

Piping

1st Year 2nd Year 3rd Year 4th Year

Near heater piping

Check heater and system piping for any sign of leakage; make sure 
pipes are properly supported.

System

Visual

Do  a  full  visual  inspection  of  all  system  components.  Ensure  all 
components  (including  boilers,  water  treatment  systems,  mixing 
valves,  circulators,  etc.)  are  operating  properly  and  have  been 
maintained.

Functional

Test all functions of the system. Perform any maintenance required 
by local codes. Verify system pressure is in the safe operating range.

Temperatures

Check control for temperature accuracy.
*Verify safe settings on Mixing Valve (if installed in system).

Electrical

Smoke and CO 
Detectors

*Verify devices are installed and working properly. Change batteries 
if necessary.

Circuit Breakers

Check to see that the circuit breaker is clearly labeled. Exercise circuit 
breaker.

Connections

Check wire connections. Make sure they are tight.

Anode

 

Rod

Remove and visually inspect the anode rod. Anode rod should be re-
placed when more than 6” of core wire is exposed at either end of 
the rod.

Relief and Drain Valve

Relief Valve

Lift  and  release  the  relief  valve  on  the  water  heater.  Make  certain 
that the valve operates properly by allowing several gallons to flush 
through  the  discharge  line.  Replace  if  valve  is  blocked  or  does  not 
operate properly.
NOTE:  TAKE  CAUTION  WHEN  OPERATING  RELIEF  VALVE. 
DISCHARGED WATER MAY PRESENT A SCALD RISK. 

Drain Valve

Open the drain valve and drain a few quarts of water from the bottom 
of the tank to flush any hard water deposits. Replace if valve is blocked 
or does not operate properly.
NOTE: TAKE CAUTION WHEN OPERATING DRAIN VALVE. DRAINED 
WATER MAY PRESENT A SCALD RISK. 

Final Inspection

Check for 
Combustibles

Check area around heater for combustible materials such as gasoline 
or paint thinner. If combustible materials are found, move away from 
the heater to a safe location.

Checklist

Verify  that  you  have  completed  the  entire  checklist.  WARNING: 
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.

Homeowner

Review what you have done with the homeowner.

Initial and Date after Inspection / Service. Continue Inspections Annually beyond 
the Fourth Year.

Table 6 - Maintenance Activities Checklist - *If Applicable to System

Summary of Contents for SSC-119

















Reviews: