background image

4 Propane safety

4.1 Introduction

WARNING: Read the warning instructions that

follow before you use the product.

CAUTION: Read the Propane Safety Manual

before you use the product.

Propane is a flammable gas. Propane can explode if the

proper cautions are not heeded. Propane is odorized

with an agent having a distinct odor that is recognizable

at very low concentrations. This helps in identifying

leaks, even when they are small.
The two greatest hazards with propane powered floor

care machines are

Emission

Fire/explosion

4.2 Emission

Propane can cause Carbon Monoxide Poisoning (C0).

CO can be lethal within as little as 30 minutes exposure

at 3,000 parts per million (ppm) concentration.
Before operating a machine using propane gas you

must be trained and certified in proper handling and

operating procedures.
If you smell propane while operating the machine:
1. Stop the engine.
2. Shut off the service valve on the propane cylinder.
3. Move the product to a well-ventilated area.
4. Remove the cylinder from the machine and take it

outside the building.

5. If the cylinder is leaking, contact an approved repair

shop to determine the cause of the leak and have

the shop, not you, repair it.

4.3 Fire/Explosion

Leaking propane containers or hoses can cause fire.

Propane vapor concentrated or confined to a small,

restricted space may explode or ignite.
Make sure that the propane container is undamaged

before attaching it to the machine.
If a fire occurs while the machine is being operated do

the following:
1. Stop the motor.
2. Shut off the service valve on the propane cylinder, if

it is possible. Be careful not to get burned.

3. Move the machine outside, if it is possible. If it is not

possible, move it to a well-ventilated area away from

flammable materials. Do not attempt to extinguish

the flame from a gas leak. If you do, the gas will

build up in the area and could reignite. Starve the

fire by shutting off the supply of gas.

4. Have the machine and cylinder inspected before

using them again.

4.4 Environment

Only use the product outdoors.

4.5 Propane cylinder

When not in use, propane cylinders always should

be stored outside in an upright position in a secure,

tamperproof, steel mesh storage cabinet. Make sure

that you store the propane cylinders according to

national regulations.

Make sure that the cylinder are securely fastened

and standing in an upright position with the service

valve closed, when transporting a it to a propane

dealer or to a job.

Only use propane motor fuel cylinder. Do not use

the common household propane cylinder.

Do not drop a propane cylinder.

Do not smoke or use a device with an open flame

when handling or transporting propane cylinders.

12 - Propane safety

888 - 001 - 

Summary of Contents for HTC 800 RXP





























Reviews: