Once the engine has warmed up release the trigger
lock
(squeeze and release the throttle) to set the throttle in
the idling position.
If restarting
after a short break, you need only
set the
throttle
trigger
half-open
using the throttle lock button. If
the engine floods, push the choke fully in to its off position,
hold the throttle trigger full on, then pull the starter cord
repeatedly until the engine starts.
Now stop the engine
and prepare the work area.
If using the water feed system, connect the unit’s
water connector to a fresh water supply
or pressurised
water container.
For advice
on the safety and suitability of this equipment
contact your local HSS Hire Shop.
There is a serious risk of personal injury
if you do not
follow all instructions
laid down in this guide.
The hirer has a responsibility to
ensure that all necessary
risk assessments have been completed
prior to the use
of this equipment.
This equipment should only be used by an operator
who has been deemed competent to do so by his/her
employer.
This equipment should be used by an able bodied,
competent adult
who has read and understood these
instructions. Anyone with either a temporary or permanent
disability, should seek expert advice before using it.
Keep children, animals and bystanders away from the
work area.
Cordon off a NO GO area using either cones,
barriers or tape, available for hire from your local HSS Hire
Shop.
Never use this equipment if you are ill,
feeling tired, or under the influence of
alcohol or drugs.
Safety goggles MUST be worn by everyone in the
work area.
This equipment generates potentially harmful
noise levels.
To comply with health and safety at work
regulations,
ear defenders must be worn
by everyone in
the vicinity.
Some materials when cut contain substances
which, when inhaled, can be harmful to health.
A
suitable mask must be worn when using this equipment.
Respiratory protective equipment is available for hire, contact
your local HSS Hire Shop for details.
Wear practical, protective clothing,
gloves and footwear.
Avoid loose
garments and jewellery that could catch in moving parts, tie
back long hair.
Ensure the work area is well lit and ventilated,
if in
doubt, ask about lighting and ventilation equipment at your
local HSS Hire Shop.
Do not work near flammable gases or liquids,
petrol or
paint thinner fumes for example
. Keep combustible
materials at a safe distance -
at least 5m.
Make sure you know how to switch this machine OFF
before you switch it ON
in case you get into difficulty.
Never leave the unit running and unattended.
Always switch the engine off and wait for moving
parts to come to rest before making adjustments to it.
Engines, especially the exhausts, get very hot so
switch OFF and allow to cool before touching
them.
GENERAL SAFETY
Pullstart
Exhaust Danger
NEVER operate petrol engines indoors or in a
confined space.
The exhaust contains gases that can kill.
Fuel Safety
NEVER refuel while the engine is hot or running.
Never smoke or allow naked lights into the area
while refuelling.
Never inhale fuel vapour.
ALWAYS mop up spillage’s as quickly as possible, and
change your clothes if you get fuel on yourself.
ALWAYS store fuel in a purpose-made sealed
container, in a cool, safe place well away from
the work area.
Make sure that everyone is warned of what you
are doing.
Check the condition of the equipment before use.
If it shows signs of damage or excessive wear, return it to
your local HSS Hire Shop.
Ensure the guard is correctly fitted and secure
before starting work.
COSHH information sheets are available from your local
HSS Hire Shop.
GETTING STARTED
A range of diamond blades is available on sale or return
to suit most applications. Contact your local HSS Hire Shop.
To
fit the
300mm abrasive or diamond
wheel, immobilize
the rear flange plate
by inserting a locking pin into the
hole in the drive belt housing.
Unscrew the flange retaining bolt
with the spanner
provided,
remove the outer flange
and
seat
the new
wheel onto the inner flange.
Refit the outer flange and screw the flange retaining
bolt back into place, DO NOT OVERTIGHTEN.
Double check
that both
flanges are secure,
the
wheel is
central and spins
freely.
Finally, ensure that the safety guard is in the normal
operating position.
Mix 5 Litres of unleaded petrol with 1 bottle of HSS 2-
Stroke oil
in a suitable container, and
fill the fuel tank.
Each tank full gives about 30 minutes use. Never add the oil
and petrol to the tank unmixed.
Set the red ON/OFF control to the ON position
by
pushing fully in, to switch OFF pull the switch back out again.
If starting from cold,
set the blue choke control to ON
by
pulling out, then push in the de-compressor button.
The unit is fitted with an operators presence lever
(OPL), the throttle cannot be operated unless the OPL is
firstly depressed.
Now,
depress the OPL
and
operate the throttle
trigger,
set
the throttle
half on
and
hold using
the trigger
lock
button.
Set the machine on a firm level surface with the
blade clear of the ground
and clear of any obstruction,
as it will rotate as soon as the engine starts.
Pull the starter cord
a few times
until the engine
'coughs',
then
push the choke in
to it's off position
and
pull the starter
once more. The engine should start.
12” Portable Cut-Off Saw
Outer Flange
Inner Flange
Abrasive Or
Diamond
Wheel
Flange Retaining Bolt
Water Feed Tap
Decompressor
Water Feed
Connector
Fuel Tank
Throttle Trigger
Trigger Lock
Button
Operator
Presence
Lever
Operator
Presence
Lever
ON/OFF
Choke
