HSM classic, Instruction Manual

Page: 3 / 4

Cutting type Strip cut Cross cut
Shred size 1/4" 1/8" 1/8" x 2" 1/16" x
5/8"
1/32" x
7/16"
1/32" x
3/16"
Sa­fety ra­ting DIN 32757 – 1 2 2 3 4 5 Level 6*
Cutting ca­pa­city (sheets), DIN A4 70 g/m
2
65 - 67 48 - 50 38 - 40 26 - 28 17 - 19 9 - 10
Weight 154 lbs. 176 lbs.
Noise level (Idle running/ load) 60 dB(A) / 68 dB(A) 60 dB(A) / 75 dB(A)
Cutting speed 24 ft./min.
Loa­ding width 15.8"
Volta­ge 115 V, 60 Hz
Power
for the maximum number of sheets
2100 W
Dimensions W x D x H 23.4" x 18.5" x 37.8"
Volume of shredded ma­teria­l ba­g 38.5 gallons
oPeratiNg iNStruCtioNS oPeratiNg iNStruCtioNS
Before changing the location, cleaning or anything else other than
normal operation
turn off and unplug the paper shredder!
Maintenance and service work may be performed only by:
• Customer service
• Spe­cial­l­y traine­d staff (e­.g. qual­ifie­d e­l­e­ctricians)
• An authorized service technician
4. insta­lla­tion
• This paper shredder should never be placed near or over a radiator or heat source.
• The ventilation slots must not be blocked or covered and they must be at a distance of at
least 4” away from walls or furniture.
• Make sure the power plug is easily accessible.
• Before plugging in the power plug, check that the voltage and frequency of your local
main supply correspond to those stated on the type plate.
Risk of injury!
Do not reach into the paper feed slot.
Risk of injury from slivers!
Wear protective goggles when destroying diskettes, CDs and hard
credit cards.
Risk of injury by pulling in!
Keep long hair, loose articles of clothing, ties, scarves, jewelry etc.
away from feed opening. Material with the tendency to form loops, e.g.
tapes, strapping material, etc. must not be shredded.
On machines with cross cutting the two red ties of the
transport retainer for the compacting unit must be removed.
inserting the ba­g
for shredded ma­teria­l
• Push frame with guide and bag into bottom frame.
• Close front door.
• Open front door and
pull out frame with bag
for shredded material.
• Fold new bag around
frame and allow to over-
lap by approx. 7.87”.
• Insert new bag
Particle cutting devices are equipped with a compacting mechanism.
Press the foot pedal in the lower part of the cabinet to shake up the
collector sack and reduce the volume of the particles. Paper can be fed
again.
Caution!
Empty the shredded material container after the paper shredder has been
switched off, because otherwise malfunctions of the cutting system could
occur when the rocker switch is pressed several times in succession
8. Ma­intena­nce a­nd ca­re
Clea­ning:
• Switch off the shredder, pull out the power plug.
• When cleaning only use a soft cloth and a mild soap-water solution. Never use scouring
age­nts, cl­e­aning fluid, pe­trol­e­um or thinne­rs.
When the cutting ca­pa­city drops or the noise increa­ses:
• Lift the inspection door on the top of the device and spray special cutting
block oil on the blade rollers of the cutting device.
• Run cutting system forwards and backwards several times without feeding
paper. Paper dust and particles are shaken off.
9. technica­l Da­ta­
Te­chnical­ and optical­ modifications re­se­rve­d.
Before sta­rt-up:
undo the wing screws securing the unit during
tra­nsporta­tion.