14
Classic 390.3
09/2011
english
10 Technical data
* HSM-speci
fi
cation
Cutting type
Strip cut
Cross cut
Shred size (
mm)
5.8
3.9
3.9 x 40
1.9 x 15
0.78 x 11
1 x 5
Sa fe ty ra ting German
DIN 32757 – 1
2
2
3
4
5
Level 6*
Cutting ca pa ci ty**
(Sheet), DIN A4 70 g/m
2
80 g/m
2
40 - 42
33 - 35
31 - 33
25 - 27
25 - 27
20 - 22
17 - 19
13 - 15
10 - 11
7 - 9
7 - 8
6 - 7
Cutting speed
126 mm/s
135 mm/s
Weight
48 kg
56 - 58 kg
Noise level
(Idle running/ load)
60 dB(A)/60-70 dB(A)
60 dB(A) / 70 - 80 dB(A)
Lo ading width
400 mm
Voltage
230 V, 50 Hz
100 V, 50/60 Hz – 115 V, 60 Hz
Power for the maximum number of sheets
1400 W
Operating mode
Continuous operation
Ambient conditions in operation:
Temperature
Relative humidity
Height above sea-level (MSL)
-10 °C to +40 °C
max. 90 %, without condensation
max. 2,000 m
Dimensions
W x D x H (mm)
595 x 510 x 915
Volume of shredded material bag
148 l
Applied standards and technical speci
fi
cations:
• EN 55014-1:2006
• EN 61000-4-2:1995 + A1:1998 + A2:2001
• EN 55014-2:1997 + A1:2001 + A2:2008
• EN 61000-4-4:2004
• EN 61000-3-2:2006
• EN 61000-4-5:2006
• EN 61000-3-3:1995 + A1:2001 + A2:2005
• EN 61000-4-6:2007
• EN 13849-1:2008
• EN 61000-4-11:2004
• EN 62233:2008
EC Declaration of Conformity
The manufacturer
HSM GmbH + Co. KG
, Austraße 1 - 9, D-88699 Frickingen hereby declares that the machine,
referred to here as
document shredder
HSM Classic 390.3
corresponds to the health and safety requirements of the following EC directives listed below due to its conception and
design of the version in which it was put into circulation by us:
Low voltage directive 2006 / 95 / EEC
EMC directive 2004 / 108 / EC
Frickingen, 01.03.2010
Rolf
Gasteier
-
Technical
Director
The machine type was tested for compliance with the requirements of the EC directives by:
the test and certi
fi
cation board of the Technical Administation Committee, c/o Verwaltungs-Berufsgenossenschaft,
Deelbögenkamp 4, D-22297 Hamburg, Germany.
This test centre is responsible according to the EC directives.
** The maximum number of sheets (DIN A4, 70 g/m² or 80 g/m²), fed lengthways, which can be cut in one cycle. The
performance data is determined when the motor is cold and the cutting device is freshly oiled. A weaker mains voltage
or a different mains frequency to the one speci
fi
ed could result in less sheet capacity and increased noise during op-
eration. The sheet capacity can vary depending on the structure and properties of the paper and on the way it enters.
The performance data in 80 g/m² is calculated.