background image

RevC 11/04/13 

 

The 

GAS  SAFE  REGISTERED  ENGINEER

  commissioned  to  install  this  appliance  is 

wholly  responsible  for  deciding  the  suitability  of  any  flue  arrangement  to  operate  in 
conjunction with this gas appliance. 
 

Points regarding the ‘Fire-bed’ 

 

  The  stove  is  supplied  with  ceramic  matrices  and  coals/logs,  which  are  to  be 

arranged by the fitter in strict accordance with the installation instructions.  The 
purchaser must not alter the layout of the coals/logs or add any extra coals/logs. 

 

  The coals/logs used in this stove to produce a realistic coal/log effect are made 

from ceramic fibre based material.  The ‘coals/logs’ may change colour after use, 
which is quite normal. 

 

  Replacement  ceramic  matrices  and  coals/logs  must  be  sourced  from  your 

approved HS Gas stockist. 

 

 

Operating the Appliance 

 

It is strongly recommended that these instructions are read and thoroughly 

understood in advance of operating this appliance. 

 

Gas Control Cover Plate 

To gain access to the gas control valve, the cover plate 
must first be opened.  The cover plate opens from the 
left and swings out, away from the stove to expose the 
gas controls. (See Diagram 1) 
 

Burner Controls 

The gas control valve is situated on the left hand side of 
the  appliance,  looking  from  the  front,  next  to  the  front 
left hand leg. 
 

Pilot Assembly 

The  pilot  assembly  is  positioned  at  the  front  of  the 
burner tray on the right hand side.   
 

 
Opening the Stove Doors (If Applicable) 

This appliance has been designed to run safely with the doors open.   
However the doors will get hot when the stove is lit.   

 

Never attempt to open or close the doors with bare hands!!! 

 

We would recommend the use of a quality heat resistant glove or gauntlet. 

 

DIAGRAM 1 

Summary of Contents for Herald 6








Reviews: