HPRT MPT-III, User Manual

Page: 2 / 2

-5- -6- -7-
-10- -9-
-8-
Chapter 2 Specifications
Chapter 3 Operation Methods
3.1 Preparation Before Using
3.1.1 Li-ion Battery Loading
1) Refer to the picture, put the battery in the battery slot, pls pay
attention to the correct positive and negative.
2) Close the battery case.
3.1.2 Paper Loading
Top Cover
Rubber Roller
Cover Open Button
Direction
3.2 Basic Function
3.2.1 Printer On
The printer is powered on by pressing the power button; t he
power indicator is on with red color whenever the printer is on.
Notice: when the battery is almost e xhausted, the LED
3.3 Interface and Printing
3.3.1 Serial Interface
This model of printer uses DB-9 serial interface cable (one end is D
model standard serial interface socket, connected to host
computer, the other end is PS/2 socket, connected to printer).
3.3.2 Infrared Ray (IR) & IrDA Interface
MPT-III can be connected to your main device through IR, RAW-IR
and IrDA can not be available at the same time. Reset the printer
if it is not the mod el you want. When printing through RAW-IR and
IrDA, make infrared ray of main device right towards to infrared ray
win dow of printer, distance shoul d be le ss than 50mm (varies with
main device), angel should be less than 30°.
3.4 LED Indicator and Buzzer Definition
There are one buzzer and two LED indicators to indicate the
printer status. LED indicators indicate current status and buzzer
indicates the changes of status.
Chapter 4 Other Information
4.1 Printer Technical Manual
Pls refer to MPT-III Series technical manual.
4.2 Preprinted Black Mark Specification
If user wants to locate receipt by detecting preprinted black
mark, it shall ac co rd to the followin g specificati on for the
black mark, otherwise it may cause printer can’t recognize the
black mark.
1) Printing position: bla ck mark shall preprint at the left si de of
receipt.
2) Width range: ≥7mm
3) Height: 4mm≤height≤6mm
4) Reflection rate to IR: <10% (reflection rate to the black mark on
paper>65% )
5) Hps: Hp s indicates the distance from down edge of detecting mark
from beginning line. (0mm≤Hps≤1mm
)
Width
Height
Hps
3.2.3 Self-test
The self-test checks the printer’s current settings, s tatus and
whether the printer has any problem . Hold dow n the [FEED]
button while press [POWER] button about 3 seconds, the selftest
begins.
T he printer is ready to receive data as soon as it completes the
self-test.
3.2.4 Paper Feeding
When printer works under non-blackm ark mode, user could
use [FE ED] button to feed paper manually. Printer will stop
feeding whe n rea ching max fe eding distance . M ax feedi n g
dist ance coul d be set by the PC soft ware “MPTT ools”, please
r efer to your distribu tor for more technical infor mation of
“MPTTools”.
3.2.5 Battery Charging
Wh en li-ion battery runs out of power, bl ue LED indic ator flash
slowly and buzzer will give up warning. It will po wer off
autom atically whe n con tin ues pri nting. If you want to go on,
please charge it.
Charging method: Plu g in socket (220V, 5 0Hz) with power adapter.
1) Power-off charging : LED li g ht will always indica te b lue color
and goes off when fully charged.
2) Power-on ch arging: LED light wil l keep blinking in blue color,
and w ill stop blinking when fully changed. Printer could be in use
when charging.
Notes: Please use the manufacturers supplied batte ry and power
The printer is off after press the [POWER] button la st for 2
seconds. All the indicators are off whenever the printer is
off.
3.2.2 Printer Off
There is software which called MPTTools. It’s software to set the
printer parameters, it used to set the baud rate of serial port,
Infrared mode, RAW-IR and VIR, it also support setting the
prin ter Bluetooth device name and password.
The instructions pls refer to MPTTools Guide.
3.5 Software Tools of MPT-III
Item Parameter
Printing
Printing Method
Resolution
Printing Speed
Valid Printing Width
Power Saving
Resident Fonts
Barcode
Graphics
Detection
LED Indicator
Power
Paper
Interface
Sleep Mode
1D
2D
Sensors
P ower Indicator
Error Indicator
Battery
Paper Type
P
aper Width
Paper Thickness
Pap
er Ro ller Diameter
P aper Loading
Power Supply
Direct Thermal Line P rinting
203dpi (8dots/mm)
RS232, USB (optional)
UPC- A, UPC -E, EAN 8, EAN13 ,
CODE 39, ITF , CODEBA R, CODE128 , CODE93
Su pport b itmap prin ti n g with differen t
de nsity and user defi n ed bitma p
prin ting (Max. 40K for per b itmap ,
an d Max. 64K for total)
P aper out detection, cover open detection
1500mAh / 7.4V
rechargeabl e Li-ion battery
Easy loading mechanism
Max. 70mm/s
72mm
YES
QR code
Red
Blue
12V 1.0A
Receipt paper
80mm
0.05~0.12mm
≤40mm
Physical
Characteristics
W orking Condition
Sto r age C ondition
0°C~40°C , 20%~85%RH
-20°C~70°C, 5%~95%RH
Dimension
W
eight
102.5(L)*110(W)*50(H) mm
325G (Without paper roll)
Software
Emulation
Driver Win d ows XP/ Vista /Win 7 /Win8/Win10
ESC/POS
1) Pull to open the top cover.
2) Put the paper into the paper case, pay attention to the directi on of
the paper. If loaded reversely, it won’t print.
3) Pull paper out of paper case.
4) Make sure paper in the center then close top cover.
adapter, otherwise cau se to printer damage and battery leakage,
light and/or explosion.
indicator blinks with blue color, in this case, y ou m ust charge
the battery by using the adaptor. The method of charging
the battery, please refer to 3.2.5.
GBK 16 × 16, 24 × 24dots
ASCII 8 × 16, 12 × 24dots
S tatus In d icator
( Blue)
Power In d icator
(R e d )
Bu zz er S tatus
ON OFF Once Power-on , rea d y
Flash Flash Twice Cover open
Flash Flash Once Paper en d
Flash OFF S ilent S tan db y
OFF Flash Once Power-on char g in g
OFF ON S ilent Power-o ff char g in g
OFF ON Three ti mes Power-on char g in g,
b a tt ery full
OFF OFF S ilent Power-o ff char g in g,
b a tt ery full
ON OFF Once Press [FEED] b u tt on
OFF OFF Twice Power o ff
Chinese
Alphanumeric
User-defined
Codepage YES
46
SDK WinCE, Win Mobile, Android