Warranty
Legrand warrants this product for a period of 3 years from the date of purchase.
These goods come with guarantees that cannot be excluded under the Australian and
New Zealand Consumer Laws. You are entitled to a replacement or a refund for a major
failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired if the goods fail to be acceptable quality
and the failure does not amount to a major failure. See the Warranty card enclosed with
this product for further details.
Customer Service
For all Customer Service and Technical Support
please call Monday to Friday during business hours.
Legrand Australia
Legrand New Zealand
1300 369 777
0800 476 009
www.hpm.com.au
www.hpm.co.nz
ABN: 31 000 102 661
4
5
6
7
Installation
Cleaning
Optional Accessories
Disclaimers
Remove all packaging from the product before commencing installation. Ensure the circuit has been isolated from the 240V mains before
commencing work.
1. Choose a suitable mounting location. There must be adequate clearances in the wall/ceiling to accommodate the Draft-stopper and/or
ducting. Refer to section 2 for further information.
2. If ducting through the wall to the outside, refer to instructions in the wall duct kit. Note: the wall kit is available separately, please refer
to Optional Accessories section.
3. The time delay module that is included in EFT150SQSWE is available separately (EF100/150TD), adjustable from 1-to-29 minutes.
4. Make a circular 160mm hole in the wall/ceiling.
5. Remove front cover / fascia by removing fixing screw and cap on the underside of the cover.
6. Remove draft-stopper if not required. Note that the draft-stopper (when fitted) has an effect on the airflow.
7. Make the electrical connections (as per Figures below).
8. Ensure orientation of fan is with arrow pointing
↑
up.
9. Fix fan firmly to the wall with the 4 screws provided.
10. Replace front cover/fascia and tighten fixing screw. Replace cap.
11. Switch on and test function. Use a paper tissue held against fan
inlet to verify suction.
This product should only be cleaned with a damp cloth. Cleaning agents and solvents should not be used. Ensure the fan is switched off from
the mains power supply before removing the grille / fascia.
Timer Adjustment
The default setting
is to 1min (approx).
Adjust to dedsired
time delay
R621/6D – 150mm wall duct kit
EF100/150TD – Time delay module allows the fan to run for a set period, adjustable between 1 - 29 mins, after the switch has been turned off.
1. This product must be installed and used as per these instructions. 2. This product is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance. 3. This product is intended for household use and similar purposes. It is not suitable for use in
an environment heavily laden with dust. Under these conditions the life of the fan motor can be significantly reduced. 4. This product should not be enclosed in thermal insulation
as it may cause the unit to overheat. 5. This product has been designed to operate in ambient temperatures -10°C to 40°C. 6. This product contains no serviceable parts and no
attempt should be made to repair it. If the product is faulty it should be discarded. 7. Airflows listed in this product indicate the product performance. Refer to the BCA (Building
Code of Australia), or similar, for the appropriate airflow required for a particular installation. 8. Ventilation products must have an adequate source of external air to ensure correct
performance. 9. Consideration must be taken in the installation of ducts to ensure that condensation that will form in the duct will not run back into the fan housing. 10. Precautions
must be taken to avoid the back-flow of gases into the room from the open flue of gas or other fuel-burning appliances. 11. This product has been designed for domestic or similar
uses and is not suitable for a commercial installation. 12. This product is not suitable for installation in hazardous and/or corrosive areas. 13. Extended exposure to UV rays (such
as exposure to direct sunlight) may cause discolouration of this product. 14. The material in this product may vary in colour from batch to batch. Colour matching from one batch to
another cannot be guaranteed. 15. This product utilises intellectual property in the form of registered designs, trademarks, and/or patents. Such intellectual property remains the
property of Legrand in all cases. 16. Legrand reserves the right to modify the specification of this product at any time.
Figure 2. Fan with timer module and light fitting
Active
L
N
LS
Neutral
Connection from rear – bring mains wiring through
cable entry hole.
Connection from side (Fan only) – use twin flat core
(H03VV-H2) or circular core (H05VV-F) 2 x 0.75mm
2
and place under cable clamp provided.
Timer
LE06397A
TB
LEG0703_B
LE06397A
TB
MINIMUM
(1 minute)
MAXIMUM
(29 minute)
LS
N
L
3
2
1
Fan
mounting
orientation
Cable entry
from rear
Cord entry from
side for plug and
lead (knock-out
provided)
LS Switched Active
from wall switch
N Neutral
L Unswitched Active
(only used when
timer module
is fitted)
Fixing screw
position of fascia
Figure 1.
LS
N
L
3
2
1
