background image

M8000 Multi-Function Home Gym 

 

E&OE 

©2017 HPF 

Included Items 

Note

: The list of included items and parts diagram are for reference. Many parts come pre-assembled. 

No. 

Description 

Qty. 

No. 

Description 

Qty. 

Base Frame 

39 

Nut M10 

27 

Upright Support Tube 

40 

Nut M12 

Rear Stabiliser 

41 

Weight Pin 

Seat Support Tube 

42 

Plastic end 

Main Support Tube 

43 

Bridge Tube End Ø60 

Leg Curl Tube 

44 

End Cap Ø60 

Guide Tube 

45 

Butterfly Arm End Cap Ø50 

Bridge Tube 

46 

Flat Cap Ø25 

Pull Unit 

47 

Pin 

10L 

Butterfly Arm Left 

48 

Rubber Ring 

10R 

Butterfly Arm Right  

49 

Pulley 

11 

11 

Handlebar 

49A 

Small Pulley 

12 

Lat Bar 

50 

Small Pulley Cover 

13 

Bottom Bar 

51 

Plastic Bushing 

14 

Leg Curl Pad Tube 

52 

Rubber Stop 

15 

Backrest Bracket 

53 

Butterfly Arm Pad 

16 

Bolt M12x80 

54 

Leg Curl Pad 

17 

Pulley Bracket 

55 

Rubber Grip 

18 

Two-Way Pulley Bracket 

56 

Bottom Bar Cover 

19 

Weight Bar 

57 

Bushing 

20 

Pulley Bracket 

58 

Selection Bar Cap 

`1 

21 

Pull Unit Axle 

59 

Backrest 

22 

Bolt M8x20 

10 

60 

Seat 

23 

Bolt M10x60 

61 

Chain (6 links) 

24 

Bolt M8x15 

12 

62 

X1 Hook 

25 

Bolt M10x40 

63 

Weight Plate (8lbs.) 

26 

Bolt M10x45 

64 

Weight Plate (10lbs.) 

27 

Bolt M10x75 

65 

Lat Bar Cable 

28 

Bolt M10x70 

66 

Butterfly Arm Cable 

29 

Bolt M12x70 

67 

Lower Pull Bar Cable 

30 

Bolt M10x80 

68 

Elbow Pad Tube 

Summary of Contents for m8000

















Reviews: