HPE SN3000B Hardware Reference Manual Download

Page: 18 / 95

Port side of the switch

Figure 6: Port side of the HPE SN3000B 16Gb FC Switch

on page 18 shows the port side of the

SN3000B 16Gb FC Switch.

Figure 6: Port side of the HPE SN3000B 16Gb FC Switch

1. System status LED

2. Management Ethernet port with LEDs

3. USB port

4. FC ports (0-3)

5. System power LED

6. Serial console port

7. Switch ID pull-out tab

8. FC ports (4–7)

NOTE:

The two LEDs on the serial console port are nonfunctional.

Nonport side of the switch

Figure 7: Nonport side of the HPE SN3000B 16Gb FC Switch

on page 18 shows the nonport side of

the SN3000B 16Gb Switch.

Figure 7: Nonport side of the HPE SN3000B 16Gb FC Switch

1. Filler panel (Optional Power supply and fan
assembly can be added in this slot)

2. Power supply and fan assembly #1

3. Power supply and fan assembly LED

4. On/off switch

5. Power plug receptacle

6. Thumbscrew

7. Handle

Port side of the switch

Summary of Contents for SN3000B
































































































Search results

Summary of Contents for SN3000B

Reviews:

Related manuals for SN3000B

Brands by name

Popular brands

HPE SN3000B, Hardware Reference Manual

Search results

Summary of Contents for SN3000B

Reviews:

Related manuals for SN3000B

Brands by name

Popular brands