HPE R/T3000 G2 User Manual Download Page 12

Page: 12 / 79

Installation 12

Installation

Precautions

Save these instructions. This document contains important safety instructions that should be followed

during installation, operation, and maintenance of the UPS and batteries.

WARNING:

A risk of personal injury from electric shock and hazardous energy levels exists.

The installation of options and routine maintenance and service of this product must be

performed by individuals who are knowledgeable about the procedures, precautions, and

hazards associated with AC power products.

37 kg

82 lb

This symbol indicates that the UPS exceeds the recommended weight for one

individual to handle safely.

WARNING:

To reduce the risk of personal injury or damage to the equipment,

observe local occupational health and safety requirements and guidelines for manual

material handling.

45 kg

100 lb

This symbol indicates that the ERM exceeds the recommended weight for one

individual to handle safely.

WARNING:

To reduce the risk of personal injury or damage to the equipment,

observe local occupational health and safety requirements and guidelines for manual

material handling.

WARNING:

To prevent personal injury from earth conductor leakage current:

•

Do not operate the UPS while disconnected from the utility power source.

•

Disconnect load devices before disconnecting the UPS from the utility power source.

Preparing to install the hardware

Before installing the hardware:

Be sure the necessary tools and materials (on page

) are available.

Select an installation site ("

Selecting a site

" on page

Prepare the equipment ("

Readying the equipment

" on page

) for installation in the rack.

Tools and materials

The following tools are required for installation:

•

Phillips screwdriver

•

10-mm hex-nut driver

The following items are supplied with the rack:

•

Screws

•

Hex nuts

•

Cage nuts

•

Cage nut-fitting tool

Summary of Contents for R/T3000 G2
















































































Search results

Summary of Contents for R/T3000 G2

Reviews:

Related manuals for R/T3000 G2

Brands by name

Popular brands

HPE R/T3000 G2, User Manual

Search results

Summary of Contents for R/T3000 G2

Reviews:

Related manuals for R/T3000 G2

Brands by name

Popular brands