background image

© 2012 • HPC, Inc. • Schiller Park, IL • 60176 • USA • www.hpcworld.com

Wall Safe Combination Changing (continued)

TO UNLOCK ON FACTORY SETTING - TURN DIAL “LEFT” 4 TURNS, STOPPING ON “43”. 
TURN DIAL RIGHT UNTIL BOLT RETRACTS.

BEFORE CLOSING UNIT, try the new combination several times, using the opening index.

TO UNLOCK ON 3 NUMBER COMBINATION - FOR EXAMPLE “50-25-50”

1. Turn the dial to the LEFT, stopping when “50” is aligned with the opening index, the FOURTH time.

2. Turn the dial to the RIGHT, stopping when “25” is aligned with the opening index, the THIRD time.

3. Turn the dial to the LEFT, stopping when “50” is aligned with the opening index, the SECOND time.

4. Turn dial slowly to the RIGHT until the bolt retracts.

TO LOCK

Turn dial to the LEFT at least four full revolutions.

CAUTION

NEVER INSERT THE CHANGING KEY IN THE LOCK WHEN THE COVER IS REMOVED.
ALWAYS BE CERTAIN THE WING OF THE CHANGING KEY IS ENTIRELY WITHIN THE 
LOCK (FIG. 2) BEFORE TURNING KEY.

WARNING

CHANGING TO A NEW COMBINATION

Make up a new combination selecting 3 sets of numbers of your own choosing. DO NOT use numbers

between 0 and 20 for your last number. (e.g. 32-74-14). For maximum security, DO NOT use numbers

ending in 0 or 5 and DO NOT use numbers is a rising or falling sequence. (e.g. 25-40-65 is not as good

a combination as 46-32-68)

1. Using the changing index, dial the existing combination as explained in paragraphs 1-2-3 above.

    The lock leaves the factory with all 3 numbers of the combination set on 50.

2. Hold the dial with the last number at the changing index, and insert the changing key in the key 

    hole in the back of the lock (see Fig. 2). Insert the key until the wing is entirely inside the lock and

    comes to a positive stop (see Fig. 2).

3. Turn key one quarter turn to the LEFT (see Fig. 3). With the changing key in this position, turn the 

    dial to the LEFT, stopping when the first number of the newly selected combination aligns with the

    changing index the FOURTH time.

4. Turn the dial to the RIGHT, stopping when the second number is aligned with the changing index,

     the THIRD time.

5. Turn the dial to the LEFT, stopping when the third number is aligned with the changing index, the

    SECOND time. Holding the dial in this position, turn the changing key back to the RIGHT and

    remove it (see Fig. 4) The new combination you have chosen is now set in the lock.

IF AN ERROR HAS BEEN MADE IN SETTING A NEW COMBINATION, we suggest that an accredited

locksmith be called.

Fig. 2

Fig. 3

Fig. 4

Wing on key passes through slot

in lock plate. (Fig. 2)

Safe Change Key

No. SLC-42

2

Summary of Contents for WS-100C






Reviews: