background image

HPE StoreFabric SN4000B
SAN Extension Switch
Quick Start Instructions

©

Copyright 2015, 2016 Hewlett Packard Enterprise Development LP

The information contained herein is subject to change without notice.
The only warranties for Hewlett Packard Enterprise products and
services are set forth in the express warranty statements accompanying
such products and services. Nothing herein should be construed as
constituting an additional warranty. Hewlett Packard Enterprise shall
not be liable for technical or editorial errors or omissions contained
herein.

*5200-0340*

Part Number: 5200-0340
Published: January 2016
Edition: 2

Overview

Read these instructions to set up and configure the
HPE StoreFabric SN4000B SAN Extension Switch.

These instructions provide basic configuration
steps. For detailed rack mount and configuration
instructions, download the HPE B-series 16Gb FC
Switches Hardware reference guide from the
Hewlett Packard Enterprise website: http://
www.hpe.com/support/sn4000b/manuals.

Figure 1 (page 1) shows the port side of the
SN4000B SAN Extension Switch.

Figure 1 Port side of the SN4000B SAN
Extension Switch

2. Power status LED

1. System status LED

4. Ethernet management port

3. USB port

6. Serial number pull-out tab

5. Console port (RJ-45)

8. 40 GbE ports (QSFP+) (2)

7. 16 Gb FC ports (24)

9. 1/10 GbE ports (16)

Verify the carton contents

Verify that the carton contains the following:

One StoreFabric SN4000B SAN Extension
Switch with two integrated power supply/fan
assemblies

Serial cable with an RJ-45 connector

An RJ-45 to DB-9 adapter

Rubber feet, required to set up the switch as
a standalone unit

Brocade EZ switch and China RoHs
documentation

Two power cords

One accessory kit with the following items:

Rack Mount Kit

Hewlett Packard Enterprise product
documentation, including Read Me First,
Quick Start Instructions, Safety Guides,
HPE SAN Visibility CD, User License, and
Warranty.

Summary of Contents for StoreFabric SN4000B








Reviews: