HP ProLiant XL730f Gen9 Server User And Maintenance Manual Download Page 42 | Manualshive

Page: 42 / 72

background image

Removal and replacement procedures 42

a.

Slide the drive into the drive cage backplane, aligning the drive screw holes with the drive cage

screw holes.

b.

Install the four drive anchor screws.

c.

Connect the drive cables.

2.

Install the drive cage.

3.

Install the access panel (on page

4.

Install the server ("

Installing the server

" on page

5.

Connect peripheral devices to the server.

6.

Power up the server ("

Powering up the server

" on page

Front panel I/O board

CAUTION:

Replace all cut cable ties during a removal and replacement procedure. Failure to

do so results in improper airflow that can lead to thermal damage.

«
...
40
41
42
43
44
...
»

Summary of Contents for ProLiant XL730f Gen9 Server









































































Reviews:

No comments

Related manuals for ProLiant XL730f Gen9 Server

DSN-4100 Series

Brand: D-Link Pages: 2

Brand: TANDBERG Pages: 187

Brand: D-Link Pages: 12

Brand: Razberi Pages: 113

LS42 - BladeCenter - 7902

Brand: IBM Pages: 194

Brand: Fujitsu Siemens Computers Pages: 68

Brand: Buffalo Pages: 2

Brand: Supermicro Pages: 62

BladeCenter PS703

Brand: IBM Pages: 198

SuperServer 6029U-TR25M

Brand: Supermicro Pages: 151

A+ AS -2114GT-DNR

Brand: Supermicro Pages: 126

Brand: QNAP Pages: 53

DIRECTORY SERVER 2.0 - GATEWAY

Brand: Red Hat Pages: 66

Brand: Planet Pages: 87

Brand: Vitek Pages: 2

Brand: Inspur Pages: 2

Brand: Gateway Pages: 151

Brand: IBM Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands